Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Sakrete Driveway & Pavers: The Arlington Owner’s Guide
Sakrete is a bagged material brand – concrete mix, paver base, polymeric sand, mortar – not a machine with a model number. So “Sakrete driveway & pavers” in Arlington means the products themselves: the base, the sand between pavers, the concrete patch, the jointing mix. When those fail, the fix is re-prepping and re-installing with the right Sakrete product for North Texas ground. Installed driveway work in Arlington runs $7,000 – $18,000 for pavers, $4,500 – $12,000 for concrete, and small repairs that stay under $2,000 are common.
Owners usually find out the hard way, after a wet spring. Sand washes out of the joints. A paver corner lifts and rocks underfoot. A patch of concrete mix crumbles at the edge of the slab where runoff pools. Or the base layer under a driveway section settles, and every paver above it starts to shift. By the time you notice, the Sakrete product that was supposed to hold it together has already lost the fight with the clay soil and the heat.
Key Takeaways
- Sakrete is a materials brand, not equipment. Matching the right product to Arlington soil and drainage matters more than the label.
- Most failures trace to base prep and water, not the bag of mix itself.
- Polymeric sand and jointing products typically need refreshing every 2 – 4 years in Texas sun.
- Licensed, insured, permits pulled where eligible, written change orders before any price change.
Which Sakrete Products This Applies To
Sakrete sells several products that show up in driveway and paver work, and they are not interchangeable. The label on the bag tells you which one you have and what it is for. Common lines include Concrete Mix (for structural pours and patching), Paver Base (a graded aggregate for bedding), Polymeric Sand (for locking joints between pavers), and mortar or jointing mixes. Read the bag before you buy a replacement; grabbing “concrete mix” when you needed polymeric sand is a common and expensive mistake.
How to identify what you have: look at the product name and the coverage or yield printed on the bag, and note the color code and the SKU on the lower corner. For a paver joint, the product has to be specifically a polymeric or joint sand, not general-purpose sand. For structural repair under a slab or a step, you need a mix rated for that use.
Original Sakrete product versus a comparable mix: Sakrete is widely stocked at Arlington-area hardware stores, which makes matching easy. A quality equivalent from another bagged brand often performs the same if the spec matches – same aggregate grade, same polymer content, same rated use. What matters is the spec, not the logo. We don’t stock parts or keep bags on a truck. Barrett & Sons Construction Arlington is an independent contractor, not affiliated with Sakrete; we specify the product and install it, and we buy the material for your job.
One Texas-specific gotcha: Sakrete’s polymer-modified mixes are made to handle our heat, but they still need the base and drainage done right underneath. If the base holds water in Arlington’s black clay, no brand of joint sand will stay put.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Sakrete Driveway & Pavers Is Failing
- Sand washing out of the joints. After heavy rain, polymeric sand thins or disappears from between pavers. The cause is usually poor drainage or an old joint fill past its service life.
- Pavers rocking or lifting at the corners. The bedding layer under them has settled or the base was never compacted correctly. Sakrete base product can’t fix a base that wasn’t graded in the first place.
- Crumbling concrete at slab edges or patches. Freeze-thaw cycles are mild here, but water pooling at a low spot and curing too fast in summer heat both weaken a mix. Edge failure is often a drainage problem, not a mix problem.
- White powdery film on the surface (efflorescence). Moisture moves through the concrete or mortar and leaves mineral salts behind. It points to water getting in where it shouldn’t.
- Sinking or dipping in one section of the driveway. Soil movement under the base. In Arlington’s expansive clay, this is one of the most common reasons a solid-looking driveway starts to fail at one spot.
Replacement Cost & What’s Included
Here are the honest installed ranges for Arlington, and what drives them up or down:
| Service | Installed price range |
|---|---|
| Paver driveway installation | $7,000 – $18,000 |
| Concrete driveway installation | $4,500 – $12,000 |
| Asphalt driveway paving | $3,500 – $9,000 |
| Driveway replacement | $5,000 – $14,000 |
| Driveway sealing | $250 – $700 |
| Paver patio installation | $3,500 – $11,000 |
The range is wide because it depends on square footage, how much base has to be removed and re-graded, drainage corrections, and whether the edges need new restraint. The mix, the base, and the joint sand are built into the quoted price – not handed to you as a separate line. Where a job is eligible, permits are pulled and inspections signed, and every price change arrives as a written change order before work happens. The 90-Day Done Right Promise is on every contract, and our crew members have up to 28 years of experience with this kind of work.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Here’s the honest split. You can safely sweep and re-sand joints with polymeric sand, clean efflorescence with a proper cleaner, and spot a drainage problem – those are the things worth doing yourself. Where DIY goes wrong is the base: replacing a sinking section, re-bedding lifted pavers, or patching a structural slab without addressing the water and the soil under it. That work is heavy, it’s easy to get the grading wrong, and getting it wrong means you’re doing it again next year.
If a section is sinking, a paver edge is lifting, or a concrete patch is crumbling, that’s the point to call us. Call (888) 590-9867 to get an exact quote – estimates are free, and we’ll tell you plainly whether you’re looking at a $400 repair or a bigger job.
FAQs
Joint sand and polymeric products typically last 2 – 4 years in North Texas sun and rain before they need refreshing, while a properly installed concrete or paver base should give you 20+ years. Lifespan depends far more on base prep and drainage than on the product itself.
Yes – often a failing section can be repaired by re-sanding joints, re-bedding lifted pavers, or patching a slab after correcting the drainage. We’ll tell you on site whether a repair will hold or whether the base needs redoing.
A joint re-sand is usually a single day, a lifting or patch repair runs one to three days, and a full driveway replacement typically runs three to seven days depending on square footage and weather. We give you the schedule in writing before we start.
We buy the specified Sakrete product – or a spec-matched equivalent – for your driveway or paver project, matched to the use and the base. You’ll see it named in the quote, so you know exactly what’s going on your ground before we pour anything. Call (888) 590-9867 for a free estimate.
Other Brands We Also Service
Driveway and paver work often sits alongside other projects on the same property. We also handle KraftMaid, Cambria, and Silestone when those come up.
If you need an honest look at what’s failing under your driveway, call Barrett & Sons Construction Arlington at (888) 590-9867 for a free estimate. A live person answers the phone 24 hours a day, seven days a week. Ask about the $40 Off Any Repair Over $200, the Free Second Opinion on Any Written Estimate, No Trip Charge Inside the County, and the permanent 10% Senior & Veteran discount.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.