Bathroom remodeling
Kitchen remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
James Hardie Bathroom Remodeling: The Arlington Owner’s Guide
James Hardie bathroom remodeling in Arlington runs $9,000 to $28,000 installed, depending on how much of the room is tile, what’s behind the old walls, and whether the shower gets a full waterproofing rebuild. We install James Hardie backer board and fiber-cement trim so your wet areas hold up against North Texas humidity and the clay soil movement that cracks older Arlington homes. You’ll usually know something is wrong when grout lines start cracking at the shower corners, caulk pulls away from the wall, or a soft spot appears near the drain pan.
Key Takeaways
- Installed bathroom remodel cost in Arlington: $9,000 – $28,000, with $5,000 – $12,000 for a smaller bath.
- James Hardie backer board doesn’t fail from water alone – it fails when it’s cut wrong, taped wrong, or installed over a moving subfloor.
- How the part differs: HardieBacker comes in 1/4″, 1/2″, and 5/16″ thicknesses, and bathroom walls and floors each need a different one.
- We’re an independent service provider. We install James Hardie products; we’re not affiliated with James Hardie.
Which James Hardie Models This Applies To
Bathroom work usually touches three James Hardie product lines, and each has its own compatibility rules. HardieBacker cement board is the wall and floor substrate behind tile, sold in 3’×5′ and 4’×8′ panels at 1/4″ (floors), 1/2″ (walls and heavy tile), and 5/16″ (floor underlayment). HardieTrim fiber-cement boards handle exterior window trim and jamb extensions on additions. HardiePanel siding shows up on ADU bathroom build-outs where the room meets an exterior wall.
The identifying step most homeowners skip: read the printed stamp on the back of the board. HardieBacker has a purple-to-greenish face and an ink stamp with the panel type. Tile set against the wrong thickness – 1/4″ where 1/2″ was required, or an interior-grade board where wet-area was specified – is a call-back waiting to happen. Measure the actual panel, check the stamp, and photograph it before the old board goes in the dumpster.
OEM vs aftermarket: for cement board, there’s no real “aftermarket equivalent.” Other brands make cement board, and some are fine, but the warranty chain changes when you mix brands with Hardie tape and Hardie mortar. We specify James Hardie panels with matching tape and screws so the installation follows the manufacturer’s published method. Where we do substitute – KraftMaid vanities, Cambria and Silestone counters in the same room – those are different product categories with their own spec sheets, not swaps for the backer board.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your James Hardie Bathroom Remodeling Is Failing
- Hairline cracks that return after re-grouting. The board underneath is moving. In Arlington’s shifting clay soils, an improperly fastened panel lets the tile crack along its joints every 8 to 18 months.
- Caulk pulling away at the shower corners and tub lip. Movement at the wall-to-pan joint, not bad caulk. The board isn’t tied to the framing the way the manufacturer requires.
- Soft spots or dark staining at the floor near the shower. Water is getting past tile and hitting the substrate. HardieBacker resists water but doesn’t stop it; a missing vapor barrier or failed waterproofing shows here.
- Tiles that sound hollow when tapped. Thin-set didn’t bond. Usually the board got dusty and wasn’t wiped before install, or the wrong mortar was used over cement board.
- Mold or efflorescence at the board’s cut edges. Cut edges weren’t sealed or the panel absorbed moisture at the backer. In a crawlspace or slab Arlington bathroom, the bottom edge is the first place this shows.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed bathroom remodels in Arlington fall in these ranges, and the number you see on the estimate should match the number on the invoice.
| Scope | Installed Range (Arlington) |
|---|---|
| Full bathroom remodel | $9,000 – $28,000 |
| Small bathroom remodel | $5,000 – $12,000 |
| Walk-in shower installation | $4,500 – $12,000 |
| Tub-to-shower conversion | $3,500 – $10,000 |
| Shower replacement | $3,000 – $8,500 |
| Vanity installation | $800 – $3,000 |
What drives the range: how much tile is being replaced, whether the subfloor needs work, whether the shower gets a full waterproofing system behind the HardieBacker, and the fixture line you pick. Every change order arrives in writing before work moves. Every eligible job pulls permits and gets inspections signed, and the written 90-Day Done Right Promise covers the work.
DIY or Call Us?
You can safely do a few checks yourself. Tap the tiles and listen for hollow sounds. Look for cracks returning in the grout. Snap a photo of the board’s stamp if you can see it through a cut in the wall. Pull up on a loose tile corner with a putty knife – no prying, no tools into the wall.
Where DIY goes wrong: the demo. Bathroom walls hide plumbing, and an Arlington bath of any age might have cast-iron drains, PVC, or a mix. Cutting into a wall to inspect the board can hit a supply line, and once the board comes off, the waterproofing has to be rebuilt to the manufacturer’s method or the new tile fails the same way. That’s the point to call us at (888) 590-9867. Free estimates, free second opinion on any written estimate you already have.
FAQs
Installed correctly, a HardieBacker shower or floor with proper waterproofing lasts 25 to 40 years in this climate. The failure point isn’t the board – it’s the joints, the fasteners, and the waterproofing layer. In Arlington’s humidity swings, a poorly sealed corner will show moisture problems in 3 to 5 years.
Sometimes. A 2-square-foot patch of cracked tile where the board is sound can be repaired. Once moisture has reached the board or the framing behind it, replacement is the only honest answer, and watering down that answer wastes your money. We’ll tell you which one you’re looking at after we see it. Call (888) 590-9867.
A shower replacement runs 3 to 5 working days. A full bathroom remodel runs 2 to 4 weeks, depending on tile scope and inspection scheduling. Tub-to-shower conversions typically take 5 to 7 days.
We buy from established building-supply sources and confirm the panel type against your specific installation before it goes on the wall or floor. Our technicians have up to 28 years of experience matching board thickness and tape to the right application.
Call (888) 590-9867 for a free estimate on your bathroom project. Standing offers: $40 Off Any Repair Over $200, Free Second Opinion on Any Written Estimate, No Trip Charge Inside the County, and a permanent 10% Senior & Veteran discount. We’re proudly serving local communities for over 29 years – founded 1998, owner-operated from day one. Ask anyone on your street, or look up the license number yourself.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.