Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Cambria Fence Installation: The Arlington Owner’s Guide
Fence installation built around Cambria-matched components in Arlington runs $3,500 to $9,000 for a typical residential run, and we’ll tell you straight: most Arlington fence jobs take one to three days once the layout and permits are settled, not a same-day drop-in. We’re an independent crew, not affiliated with Cambria, so we source the right posts, panels, and hardware to your model and spec rather than pushing a house brand.
Owners usually figure out something’s wrong one of two ways: a gate sags off-square after a spring storm out of the southeast, or the panel line goes crooked the summer after install because the footings weren’t set for our clay. Then the phone call comes. We’ve walked enough Arlington backyards to know the difference between a part failure and an install failure, and that distinction decides what you actually pay to fix.
Key Takeaways
- Installed range in Arlington on this page: $3,500 to $9,000, driven by line length, gate count, and soil conditions.
- Our technicians have up to 28 years of experience setting posts for North Texas clay and caliche.
- Every price change arrives as a written change order before work happens.
- Permits pulled and inspections signed on every eligible job.
- 90-Day Done Right Promise in writing on every fence we build.
Which Cambria Models This Applies To
Cambria’s fence line covers the reserve-profile and estate-profile series, and the model tag is usually stamped on the inside face of the gate stile or on a small plate riveted to the terminal post cap. If the tag is gone, measure the post spacing center to center and the panel height instead: reserve-profile panels sit at 6 feet nominal with posts on 8-foot centers, while estate-profile runs climb to 72-inch panels on 8-foot centers with a heavier 4×4 or 6×6 post. That spacing tells us which bracket family and cap width you need before we ever load material.
The OEM-versus-aftermarket decision matters more here than most homeowners expect. Cambria’s own caps, post skirts, and hinge sets are powder-coated to match the panel color lot, and an aftermarket cap in a “close enough” color will read as a different shade under our hard afternoon sun within a season. On brackets and hinges, though, a quality aftermarket stainless piece often outlasts the original galvanized hardware. So we’ll spec OEM for anything visible and color-matched, and reach for heavier aftermarket hardware where it does real work. We also install KraftMaid, Silestone, and Kohler products on other jobs, and we treat a fence part the same way: match the spec, don’t guess.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Cambria Fence Installation Is Failing
- Posts leaning after a rain. Our expansive clay soil swells and shrinks with every wet-dry cycle, and an undersized footing lets the post walk out of plumb. That’s a footing problem, not a panel problem.
- Gate sagging or dragging the ground. Usually a worn hinge barrel or a hinge screwed into a hollow panel edge instead of a reinforced stile. The hinge fails because it was never anchored to solid material.
- Rust bleeding from caps or brackets. Galvanized hardware in North Texas takes a beating from humidity and sun, and once the coating pits it rusts from the inside out. It shows first at the fasteners.
- Panels wobbling in the wind. A loose panel often means a bracket or clip failed, or the post spacing drifted out of spec during install. Wind in Arlington finds it fast.
- Color fading unevenly on one side. Sun-facing panels fade at a different rate than shaded ones, and a mismatched color lot shows up as a stripe. It’s cosmetic until the coating starts chalking.
If you’re seeing two or more of these, call us at (888) 590-9867 and we’ll come look before you spend on parts that may not fix the real cause.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
| Item | Installed range |
|---|---|
| Full Cambria-matched fence install (typical residential run) | $3,500 – $9,000 |
| Gate repair or hinge/bracket swap | Quoted per job, often covered under the $40 Off Any Repair Over $200 offer |
| Post reset (footing corrected) | Line-itemed in your quote |
What moves you up or down the range: total linear feet, gate count, whether soil is clay or caliche, and how many existing posts can be saved. We quote parts and labor as separate lines so you can see exactly what the hardware costs and what the work costs. Every scope, every allowance, and every price change is in a written change order before we start, so there’s no surprise invoice at the end. Fence work is backed by our 90-Day Done Right Promise, written on the contract.
DIY or Call Us?
You can safely check a lot of this yourself: measure post spacing, look for rust at the fasteners, confirm the model tag, and note where the gate drags. What goes wrong for homeowners doing the install is footing depth and soil prep. A post set too shallow in our clay will lean by the next wet season, and by then you’ve buried the cost twice. Setting posts to proper depth and compaction is where a trained crew earns the money. The 10% Senior & Veteran discount is permanent, and we offer a free second opinion on any written estimate you already have. Call (888) 590-9867 for a free estimate.
FAQs
How long does a Cambria fence installation last in Arlington? A properly set fence here runs 15 to 20 years, and the hardware often fails before the panels do. Our clay soil and summer sun are the two things that shorten that, so footing depth and coated, color-matched hardware matter most.
Can it be repaired instead of fully replaced? Often yes. A sagging gate or rusted bracket is a hardware and anchoring fix, not a full teardown, and we’ll tell you honestly which one you need. Call (888) 590-9867 and we’ll come look before you commit to a replacement.
How long does the swap take? Most residential fence projects in Arlington take one to three days once layout and permits are handled. Gate and bracket repairs are often a half-day. Call (888) 590-9867 for an exact timeline on your yard.
How do you source the part? We match OEM caps, skirts, and hinges to your Cambria model for color, and spec heavier aftermarket stainless where it does structural work. We don’t carry stock on a truck, so we order to your job and confirm the part before install. Call (888) 590-9867 to start with a free estimate.
Ready to stop guessing whether it’s the part or the install? Call Barrett & Sons Construction at (888) 590-9867 for a free estimate with line-item pricing, permits pulled, and a written 90-Day Done Right Promise. Every eligible job gets permits pulled and inspections signed, and a live person answers the phone 24/7.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.