Home additions & ADU
Kitchen remodeling
Bathroom remodeling
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Silestone Home Additions & ADU: The Arlington Owner’s Guide
We install Silestone-compatible home additions and ADUs in Arlington, and most projects land between $45,000 and $130,000 depending on scope, foundation, and finishes. We don’t promise same-day work on an addition because nobody builds one in a day, and anyone who says otherwise is quoting you a fantasy. What you get is a written scope, permits pulled, and a schedule you can actually plan around.
Owners usually come to us after a first attempt went sideways. The story is nearly always the same: a slab was poured without engineering, a conversion failed rough framing inspection, or a finish quote on the Silestone surfaces came in thousands over what was phoned in. The discovery moment is a failed inspection or a change order that shows up after the fact. That’s the point where people start looking for a contractor whose name they can look up before they sign.
Barrett & Sons Construction is an independent service provider and not affiliated with Silestone. We install Silestone and other premium surfaces into additions built to hold them.
Which Silestone Models This Applies To
Silestone is a quartz surface, so the “model” that matters for an addition is really the slab series and thickness you’ve chosen for counters, vanities, and wet bars. The common residential lines are the standard 2 cm and 3 cm slabs, and the 3 cm is what we recommend for any overhang past 12 inches in a kitchen or a bar. Get the slab series name off the original invoice or the fabricator’s sticker; if you can’t find it, measure the visible edge. A 2 cm slab reads about 3/4 inch at the edge, and a 3 cm reads about 1 1/4 inch.
For an addition or ADU, the compatibility question isn’t usually “which part fits” but “which substrate and edge profile will hold this slab.” Silestone doesn’t handle a cantilever over 12 inches without a corbel or steel support, and seams need to land where a cabinet run or a sink cutout won’t stress them. We spec the cabinet run and the seam layout before the slab is templated. If a Silestone fabricator tells you a seam location can move after template, that’s a red flag worth asking about.
On the OEM-versus-aftermarket question: for Silestone, there’s no aftermarket equivalent for the slab itself. There are cheaper quartz lookalikes sold under other names, and we steer clear of mixing them into the same run because the color and texture read differently once daylight hits. When we quote an addition in Arlington, we name the Silestone series in writing so you can price the slab yourself.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Silestone Home Additions & ADU Is Failing
“Failing” for an addition or ADU usually means one of the support pieces gave out, not the slab itself. Here’s what to look for:
- Hairline cracks at inside corners of a Silestone counter. Usually a sign the cabinet frame settled or the substrate flexed. Quartz doesn’t flex like granite, so it cracks at the weakest point.
- Sticking doors and windows in the new space. Foundation movement. In Arlington’s shrink-swell clay, a slab poured without proper pier depth will shift the first dry summer and show up as binding doors.
- Cracks where the addition meets the original house. The tie-in joint failed or the roofline wasn’t flashed correctly. Water gets in, framing swells, and the drywall line opens up.
- Moisture or mold smell in a garage conversion. A garage slab isn’t built to interior moisture standards. If the conversion skipped a vapor barrier and new slab, you’ll smell it within a season.
- A change order that appeared after work started. Not a physical failure, but the failure that matters most to our customers. Scope that wasn’t on paper is a surprise waiting for a date.
Our crew members have up to 28 years of experience, and the tie-in joint and the foundation are the two we’re called out on most in Arlington.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what these projects run in Arlington. These are installed ranges, and the top of each range is what you’ll pay for full finishes and Silestone surfaces throughout:
- Home Addition: $45,000 to $130,000
- ADU Construction: $90,000 to $220,000
- Garage Conversion: $30,000 to $80,000
What drives the range is foundation, roof tie-in, and the finish level. A garage conversion with a Silestone vanity and standard cabinetry lands near the bottom. An ADU with a full kitchen, 3 cm Silestone counters, and a separate utility meter lands near the top. Every scope, every allowance, and every price change arrives as a written change order before the work happens. Permits are pulled and inspections signed on every eligible job. The job is backed by our written 90-Day Done Right Promise: if something’s wrong, Tom comes back and makes it right.
DIY or Call Us?
What you can check yourself: measure the pick-up joint where the addition meets the house, look for daylight in the seam or a crack in the drywall line, and look at the slab for cracks at inside corners. Take photos and put a level on the floor edge of the new space. That’s diagnosis, and it’s safe.
Where DIY goes wrong is structural. Silestone over an addition can’t be re-supported by shimming a cabinet or sliding a wedge under a counter, and a failed tie-in joint means water is getting into framing you can’t see. Pulling a cabinet to “see what’s behind it” often means re-templating the Silestone, which is a bigger bill than the original repair. And a garage conversion that skipped the slab and vapor barrier can’t be fixed with a dehumidifier.
If your piece has moved, cracked, or the inspection failed, call us. We’ll look at it and give you a written number before anyone touches your Silestone. Call (888) 590-9867 to schedule your free estimate. We’re happy to compare against any written estimate you already have as a free second opinion.
FAQs
Twenty-five to fifty years on the structure if the foundation and flashings are built for North Texas clay, and the Silestone itself is good for the life of the home. The variable is the slab. Arlington sits on expansive clay that swells in wet springs and shrinks hard in dry summers, so pier depth and grade are what decide how long the addition holds. Call (888) 590-9867 for an exact quote based on your site; estimates are free.
Sometimes, yes. A single hairline crack at an inside corner can often be repaired, and a sticking door can be adjusted if the framing is sound. But a failed tie-in joint, a settled slab, or a missing vapor barrier under a conversion is a replacement-level problem. We tell you which you’re looking at in the free estimate, in writing, so you can decide.
A garage conversion runs four to eight weeks, a home addition runs three to five months, and a full ADU runs four to seven months in Arlington, depending on permits and inspections. We don’t quote a schedule we can’t hold. The inspector works for you, not for us, so we build in the time to pass the first time. Call (888) 590-9867 for a schedule tied to your specific plan.
We name the Silestone series and slab thickness in the written scope, then template after the cabinets and substrate are set, so the slab gets cut for the space it actually sits in. We don’t claim stock of any part and no parts ride on our trucks. The slab is ordered and fabricated for your job, and the fabricator’s template and install are part of the written scope. Call (888) 590-9867 and we’ll walk you through it.
Whether you’re building an addition, converting a garage, or building a full ADU in Arlington, we’ll put the scope, the Silestone series, and every allowance on paper before a nail moves. Calls are answered by a live person, 24 hours a day, 7 days a week, at (888) 590-9867. Ask for a free estimate, and ask for your free second opinion if you’ve already got a number in hand. Senior and veteran households get a permanent 10% off. And if you’re working with other brands on the same job, we install KraftMaid, Cambria, and Kohler as well.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.