A Barrett company - serving Arlington, TX
K

Kohler Kitchen Remodeling in Arlington, TX

Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Kohler Kitchen Remodeling: The Arlington Owner’s Guide

A Kohler kitchen remodel in Arlington typically runs $14,000 – $45,000 installed, and the range depends on cabinet layout changes, Kohler fixture and faucet selections, and whether walls move. We install Kohler sinks, faucets, soap dispensers, pot fillers, and appliance trim-out as part of full kitchen work, and we source each part to the exact model so nothing gets retrofitted with a wrong-size piece. Most Arlington homeowners start with one small failure: a Kohler faucet that drips from the spout a day after the handle’s shut, a sink that flexes on an undermount clip, or a soap dispenser that stopped pulling. Those little symptoms are usually the first thing that gets a kitchen project talked about at the kitchen table.

Call (888) 590-9867

Which Kohler Models This Applies To

Kohler’s kitchen line splits into a few families, and the part you need lives inside the family, not the finish. The Bellera, Simplice, K-Roscoe, Cruette, and Graze pull-down faucets share a similar cartridge diameter but differ in hose length and spray-head thread, so a “universal” replacement cartridge that fits a Simplice often won’t seat in a Bellera collar. Kohler sinks like the Whitehaven, Riverby, and Strive use brand-specific undermount clip kits, and trim-out holes on the Strive are cut to Kohler’s spec, which is why a generic drain flange can sit proud on a Strive base.

To identify the right part, read the model number stamped on the faucet base or under the sink rim, not the number on the box the fixture came in. Kohler’s kitchen cartridge and spray-head parts carry a Kohler part number starting with a model prefix, and that number is what a parts counter or supplier needs. OEM Kohler parts match the original fit, finish, and sealing surfaces. A good aftermarket equivalent can cost half as much, but the fit tolerance is where owners get burned: an off-brand O-ring on a Kohler pull-down often weeps within a year in Arlington’s hard water. We’re an independent service provider and not affiliated with Kohler; we source parts by model number from authorized suppliers so the fit is right the first time.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Kohler Kitchen Remodeling Is Failing

  • A steady drip from the spout. In a Kohler single-handle faucet, this is almost always a worn ceramic cartridge seal, not a loose handle. The cartridge’s ceramic plates wear flat against hard water scale, and the drip gets worse as the seal thins.
  • Water pooling around the sink rim. The undermount clip kit or the silicone seal has failed. On a Kohler Whitehaven or Riverby, a failed clip lets the basin drop a fraction of an inch, and water finds the gap every time you wash dishes.
  • A pull-down spray head that dribbles or won’t seat. The spray-head thread or the internal diverter has failed. Kohler changes the thread spec between model years, so a replacement head from a different model line won’t lock into the hose collar.
  • Low flow at the aerator or a sputtering stream. Mineral scale in Arlington’s water plugs the aerator screen or the cartridge inlet. A cartridge swap usually solves it; a bad aerator swap is a five-minute fix.
  • A soap dispenser that stopped pulling. The pump tube or check valve has hardened. On Kohler dispensers the tube is model-specific, and a generic replacement tube often won’t seal to the pump head.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

In Arlington, the kitchen work that addresses these failures falls into a few honest ranges. A full kitchen remodel runs $14,000 – $45,000; a small kitchen remodel runs $9,000 – $20,000. If the job is cabinet and counter work around the Kohler fixtures, cabinet installation runs $4,000 – $13,000 and countertop installation runs $2,000 – $6,500. A backsplash runs $800 – $2,500, and a kitchen island runs $3,000 – $10,000.

What drives the range up is layout change, custom cabinetry depth, and the fixture tier: a Kohler pull-down with a matching soap dispenser and a pot filler adds real money to the fixture allowance. What keeps it down is keeping the plumbing where it already sits. Every scope, allowance, and price change arrives as a written change order before work happens. Every completed job is backed by the written 90-Day Done Right Promise.

Parts and labor are quoted as line items so you can see what the Kohler part costs versus the install time. If a cabinet box has to come out to reach a sink clip or a faucet cartridge, that labor is spelled out, not folded into a lump.

DIY or Call Us?

Some of this you can check yourself safely. Turn off the supply stops under the sink and look for a weeping cartridge base, a loose spray hose, or a clip that’s backed off. Replacing an aerator screen, a soap dispenser pump, or a spray head where the thread matches is a reasonable weekend job.

Where DIY goes wrong: pulling a cartridge from a Kohler single-handle faucet without the right puller can crack the valve body, and reseating an undermount sink clip without proper support lets the basin drop and crack the countertop cut. If the sink or faucet ties into a new cabinet run, a counter cut, or a wall move, that work belongs in the scope with a permit where required. We’re licensed and insured, and our technicians have up to 28 years of experience matching Kohler parts to the right model. Call (888) 590-9867 for a free estimate, and we’ll tell you honestly whether it’s a part swap or a kitchen plan.

FAQs

Need Construction help nationwide? Licensed & insured · free written estimates
Call (888) 590-9867
Local Service Coverage

Request a Free Estimate in Arlington

Tell us what you need - Barrett & Sons Construction Arlington responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Call Now - 24/7 Dispatch