Bathroom remodeling
Kitchen remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Moen Bathroom Remodeling: The Arlington Owner’s Guide
Bathroom remodeling built around your existing Moen fixture in Arlington typically runs $9,000 – $28,000, and most projects start with a free written estimate rather than a same-day visit. You land on this page because something already went wrong: a Moen valve that drips after you shut the handle, a shower cartridge that won’t hold temperature, or a finish peeling off a Moen trim kit you installed hoping it would last. In Arlington we see a lot of this in homes built between 1995 and 2010, where the original Moen 1222 or 1225 cartridge has quietly been the weak link for a decade or more. Plenty of owners call us at that point, unsure whether to replace the part or rethink the whole bathroom.
Key Takeaways
- Installed bathroom remodel pricing in Arlington lands between $9,000 and $28,000 depending on scope, fixture reuse, and how much tile gets replaced.
- Moen sells replacement cartridges for most common valves, so a failed part does not automatically mean gut the bathroom.
- We are an independent remodeling contractor in Arlington, not affiliated with Moen.
- Every eligible scope gets permits pulled and inspections signed. No written change order, no price change.
Which Moen Models This Applies To
Moen has two broad valve families that matter for remodeling, and the cartridge inside tells you which one you have. The 1200 series uses a brass-bodied cartridge, most often the Moentrol 1222 (pressure-balancing) or the Posi-Temp 1225 (non-pressure-balancing). The newer 1255 cartridge fits the M-CORE and M-PACT-compatible valves and has a plastic body with a distinct O-ring stack. Pull the handle and look at the top of the cartridge: a brass cap with a squared top means 1222 or 1225, and a plastic body with a retaining clip means 1255. Measure the cartridge length before you buy anything. A 1222 and a 1225 look identical to most people but are not interchangeable in every valve, and that mismatch is the number one reason a Moen cartridge repair fails a second time in the same Arlington bathroom.
OEM versus aftermarket: for Moen specifically, we install OEM cartridges. The $8 aftermarket copies on the shelf do not hold up to Arlington’s hard water, which runs high in calcium and chloramine. OEM Moen cartridges cost more, usually $25 – $55, and last roughly six to ten years in most Texas households.
We are an independent service provider. We’re not affiliated with Moen, we just know their parts well enough to match the right one to your valve.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Moen Bathroom Remodeling Is Failing
- Dripping from the spout after the handle is fully off. The cartridge seal has failed and water is bypassing the stop. In a Moen single-handle valve, this is almost always the 1222 or 1225 cartridge.
- Water temperature won’t hold. A pressure-balancing cartridge has a spool that sticks; the shower runs hot then cold as the spool binds. This is common in Arlington homes where the valve has sat unused in a guest bath.
- Handle feels stiff or grinds. Mineral buildup inside the cartridge body, usually from hard water, is the culprit. It’s a sign the part is near the end of its life.
- Water leaks behind the wall. The cartridge’s retaining nut or O-ring has failed, and moisture is wicking into the wall cavity. This is the one to fix before drywall starts to show damage.
- Finish flaking or pitting on the trim. The finish itself fails separately from the valve; if the valve internals are fine, a trim kit swap may be all you need.
Replacement Cost & What’s Included
For Arlington, our installed bathroom remodel range is $9,000 – $28,000 for full-scope work, and a smaller remodel with a Moen valve refresh typically lands $5,000 – $12,000. If the scope is just the valve and trim with no tile touched, expect the smaller end of that range. What drives the price: how much tile behind the valve wall has to come out, whether the shower is a tub-to-shower conversion ($3,500 – $10,000) or a walk-in shower install ($4,500 – $12,000), and whether the vanity ($800 – $3,000) is part of the job.
You get a written line-item quote before anything starts, permits pulled and inspections signed on eligible work, and a 90-Day Done Right Promise on the install. Any price change comes as a written change order before the nail goes in.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
You can safely shut off the water at the valve stops, remove the handle, and check which Moen cartridge you have. You can also identify whether the drip is at the spout or behind the wall. What you should not do yourself is pull a cartridge that’s been seized for fifteen years in a drywall cavity. It’s a wet, tight job with a shutoff that may or may not hold, and the risk of a broken housing behind the tile is a bigger repair than the cartridge itself. Call (888) 590-9867 and we’ll walk you through what the remodel would cover.
FAQs
Six to ten years is typical for a cartridge in Arlington’s hard water, and shorter if the valve sits unused. Call (888) 590-9867 for a free estimate on replacement.
Yes. A Moen 1222 or 1225 cartridge swap is often all that’s needed if the tile and valve body are intact. A full remodel makes sense when the valve body is corroded or you’re updating the shower anyway. Call (888) 590-9867 to schedule a free estimate and see which way it goes.
A cartridge-only replacement is a few hours. A full bathroom remodel in Arlington runs two to four weeks depending on scope. We’ll write the timeline into the estimate before you sign anything.
We match the cartridge to the valve by part number and confirm the valve model before ordering. We don’t carry parts on a truck; the part is ordered specifically for your job, which is why the match is right the first time.
We also install KraftMaid, Cambria, and Silestone in the same Arlington bathrooms when a remodel goes beyond the valve itself.
Talk to Us About Your Arlington Bathroom
If a Moen valve is failing in your Arlington bathroom and you’re weighing repair against remodel, start with a free, written estimate. We pull permits, we quote line by line, and the 90-Day Done Right Promise goes on the paperwork. Call (888) 590-9867 to schedule your free estimate.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.