Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Moen Driveway & Pavers: The Arlington Owner’s Guide
A Moen-equipped paver or driveway joint control system in Arlington generally runs $250 – $700 for a single repair and $7,000 – $18,000 for a full paver driveway install, including the base work and joint materials. Most Arlington homeowners find out something failed the same way: a paver lifts after a hard rain, a joint opens up along the driveway apron, or a hairline crack shows up in the control joint where the walk meets the garage slab. That’s usually a base, bedding or joint-material problem, not the paver itself, and Moen-compatible hardware is only one piece of a system that has to handle North Texas clay.
Which Moen Models This Applies To
Moen is a plumbing brand first, and most Arlington buyers who ask for Moen hardscape components mean the Moen/Tenured-style paver joint and edge-control line sold through landscape suppliers. That said, Moen sells far more faucets and shower cartridges in Arlington than driveway hardware, and the fit issues we see usually trace back to mixing a Moen-compatible joint material with a non-matching edge restraint and a base spec that wasn’t built for the brand’s expansion rates. Identify the part before you order: the recess and joint width, the paver thickness, and the model number stamped on the edge channel or joint insert. OEM Moen parts cost a little more but guarantee the exact dimension. Quality aftermarket equivalents run 30 – 40 percent less and often work fine on flat, low-traffic drives; on a sloped Arlington driveway near a retention swale, we lean OEM because the tolerance is tighter. We’re an independent contractor and not affiliated with Moen, so we check the actual part number on your label against the brand spec before ordering anything.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Moen Driveway & Pavers Is Failing
- Paver lifting near the apron: water is pooling under the joint and the base has washed out. In Arlington’s clay soil, this one shows up fast after a summer storm and gets worse every rain.
- Open control joints: the joint insert or sealant has pulled away, letting water into the bedding course. A section that has shrunk below the paver face is a sealant failure, not a paver failure.
- Rocking pavers in the middle of the drive: the bedding sand under the Moen edge channel has shifted or the base was never compacted to spec. Pressure washing doesn’t fix this; it exposes it further.
- Hairline cracks along a straight line: a crack that follows a clean line usually means the edge restraint has moved or a joint is short, not that the paver itself broke.
- Weeds or silt pushing through joints: the joint material has lost adhesion or the base is holding water. Both point to a drainage and base problem upstream of the part.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Arlington, the actual Moen-compatible part and joint repair on a section of driveway runs $250 – $700, which covers removal of the failed insert, base recompaction, new joint material, and resetting the pavers. A full paver driveway install starts at $7,000 and reaches $18,000 on a big lot with real slope and a retainment edge. A concrete driveway replacement sits at $5,000 – $14,000, and a paver patio is $3,500 – $11,000. The range is driven by square footage, base prep, drainage corrections, and whether an old concrete apron has to be demoed first. What you’ll see on the written estimate is a line for materials, a line for base and labor, and a line for disposal. Change orders are in writing before work moves. Work carries the 90-Day Done Right Promise on every eligible job. We also handle KraftMaid, Cambria, and Silestone on the interior side if the same drive leads to a kitchen or bath project.
DIY or Call Us?
What you can safely check yourself: look at the joint width along the driveway, photograph the label on the Moen edge channel, and note where the pavers have lifted or the joint has sunk. Those three things tell us whether this is a section repair or a base problem. Where DIY goes wrong is the base. Most Arlington drive failures we see started with a homeowner who replaced the joint material over an uncompacted, water-logged subbase, and the new joint failed in the first rainy season because nothing under it had changed. If the pavers are rocking or the drive slopes toward the house, stop and call. To schedule a free estimate, call Barrett & Sons Construction at (888) 590-9867. A live person answers, day or night.
FAQs
Expect 3 to 7 years on a properly based, correctly drained Arlington driveway, and less on a drive near a slope or a retention swale where water sits. The part itself often outlasts the base under it, which is why we inspect the subgrade before we quote the material. Call (888) 590-9867 for an exact quote on your drive; estimates are free.
Yes. Section repairs are common and cost $250 – $700 in Arlington. If the failure is a joint insert or a sunk edge channel with sound base under it, we reset the part and recompact. If the base is washed out, the honest answer is a full section replacement. Call (888) 590-9867 to schedule a free inspection.
A single-section Moen joint repair takes about half a day; a full paver driveway install runs two to four days depending on square footage, base depth, and whether an old concrete apron needs demo. Permits are pulled on every eligible job. Call (888) 590-9867 to get a realistic timeline for your Arlington driveway.
We match your stamped model number to the Moen spec and order through the same landscape suppliers we use for the drive. We don’t claim to stock parts on a truck. We also offer a free second opinion on any written estimate you’ve already been given, and a $40 discount on any repair over $200. Call (888) 590-9867 to start.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.