Home additions & ADU
Kitchen remodeling
Bathroom remodeling
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Moen Home Additions & ADU: The Arlington Owner’s Guide
We build home additions and detached ADUs for Arlington homeowners, and when a Moen fixture sits inside the new bath or kitchen, we install it to Moen’s spec so the trim, valve, and rough-in all match the model line you bought. A finished addition in the Arlington market runs $45,000 to $130,000, with ADUs higher, and this is planned work, not emergency work – we schedule an estimate and a build calendar, and we don’t pretend otherwise. Most owners land on this page a specific way: the new vanity faucet drips two months after move-in, the shower cartridge sticks, and suddenly the part matters more than the room. That’s where we can help.
Key Takeaways
- A home addition in Arlington runs $45,000 to $130,000; an ADU runs $90,000 to $220,000.
- Moen parts are matched by model number, not by eyeballing the old piece.
- Hot North Texas water shortens cartridge life; it’s water chemistry, not a bad brand.
- Permits get pulled and inspections signed on every eligible job – the inspector works for you.
- Every price change arrives as a written change order before work happens.
Which Moen Models This Applies To
Moen is one of the most widely installed fixture brands in Texas homes, and the model line matters when a part fails. Single-handle tub and shower valves differ from widespread lavatory faucets; the popular 1222 and 1225 cartridge family (the brass-bodied ones behind many decades of single-handle valves) is not the same part as the newer Duralock push-in cartridges on current single-handle faucets. Getting this wrong is the number-one compatibility mistake we see: an owner buys a cartridge that looks right, forces it, and the valve body is damaged.
To identify the right part, look for the model number stamped on the back of the faucet body, inside the escutcheon plate, or on the underside of the spout. If the label is gone, photograph the handle and the escutcheon and bring the numbers to the counter. Moen keeps parts support deep across its lines, which is a real advantage for Arlington owners. The OEM-versus-aftermarket decision is straightforward: Moen-brand or Moen-authorized replacement parts are the safe call for cartridges and valve internals. Generic aftermarket cartridges can fit the threads but fail sooner, and that’s the wrong place to save $8. Barrett & Sons Construction Arlington is an independent builder and is not affiliated with Moen.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Moen Home Additions & ADU Is Failing
The “part” here is usually a Moen fixture inside the addition. Here’s what failure looks like, and why:
- Drip from the spout when the handle is off. A worn cartridge seat lets water past the seal. It starts as a slow drip and gets worse, not better.
- The handle feels stiff or grinds. Mineral scale from North Texas water builds on the cartridge stem. Left alone, the stem corrodes and the handle can snap.
- Water temperature wanders. A failing pressure-balancing or thermostatic cartridge can’t hold temp when another fixture runs – a scald risk in a new shower.
- Low or uneven flow at the aerator. Often sediment caught in the aerator screen, sometimes a clogging cartridge inlet. Cheap to check, easy to misdiagnose.
- A slight leak at the base of the faucet or behind the wall. Usually a worn O-ring or a loose mounting nut – but if water shows at the drywall, stop using it and call. Water behind the wall in a new addition is a bigger problem than the faucet.
Replacement Cost & What’s Included
When a Moen fixture inside an addition needs attention, repair or replacement is typically a small, defined job. Here’s the Arlington range:
- Cartridge or stem replacement (moen single-handle): $90 to $220, parts and labor.
- Aerator or spout replacement: $60 to $150.
- Full single-handle faucet replacement (lavatory): $200 to $450 installed.
- Shower valve or trim replacement: $250 to $650 installed, more if the wall has to open.
- Faucet swap as part of a larger addition touch-up: quoted line-item on the written scope.
The range depends on model, access, and whether anything behind the wall is wet. We quote parts and labor as line items so you see where every dollar sits. Every eligible job carries the written 90-Day Done Right Promise – if it’s not right, one call brings Tom back.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Some of this is fair to check yourself. Aerator screens unscrew by hand, and you can flush one clean. You can shut off the water under the sink and inspect for a loose mounting nut. That’s the safe list.
The rest deserves a pro. Opening a shower valve means shutting water at the main, confirming it’s off, and knowing that a corroded valve body can shear inside the wall – and that $90 part turns into a wall repair. If water is showing at drywall or a valve feels frozen, stop and call. Also worth knowing: the Moen cartridge warranty covers the part, not the labor or the water damage. We’re up to 28 years of experience on our crews, we pull permits and sign inspections on eligible jobs, and every price change comes as a written change order first. Call (888) 590-9867 and we’ll schedule a free estimate.
FAQs
Expect roughly 8 to 12 years on a Moen cartridge in this area, sometimes shorter in homes with hard water. North Texas water carries more minerals than the national average, and mineral scale is the main cause of early failure. If your cartridge is over a decade old and dripping, replace it before it fails mid-shower and a scald risk shows up. Call (888) 590-9867 for an exact quote – estimates are free.
Often yes. A dripping single-handle Moen is usually a cartridge or O-ring, and a $90 to $220 repair beats a full faucet swap. If the valve body is corroded or the trim is cracked, replacement is the honest call. We’ll tell you which one you’re facing on the estimate, not after the work starts.
A cartridge or faucet swap is typically a 45-minute to two-hour visit once the right part is on hand. That’s the catch: the part has to be matched to the model number first, and that’s the step most DIY jobs skip. We come with the model identification done.
We match your model number to the correct Moen or Moen-authorized replacement part and quote it as a line item, so you see the part cost and the labor separately. We don’t stock parts on a truck and don’t claim to. We also handle KraftMaid, Cambria, and Silestone on the room-side work if the addition needs cabinetry or counters while we’re there.
Ready to Price the Job?
Whether you’re planning a full addition in Arlington or just need a Moen fixture sorted inside one already finished, we’ll give you the numbers straight. A live person answers the phone 24 hours a day, 7 days a week – not a voicemail box. Call (888) 590-9867 for a free estimate. Current offers: $40 off any repair over $200, a free second opinion on any written estimate, no trip charge inside the county, and a permanent 10% senior and veteran discount.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.