Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Kitchen Remodeling: The Arlington Owner’s Guide
Quick answer: We install Schluter-compatible kitchen remodeling in Arlington, including uncoupling membranes, waterproofing board, and shower/wet-area systems, with typical kitchen remodel pricing of $14,000 – $45,000 depending on scope. Because this is a planned project – not an emergency – we do not promise same-day installs; instead, you get a free on-site estimate, a written scope, and a scheduled start date. Owners usually reach us at the point where a tile floor has cracked along a grout line, a corner of the membrane is lifting, or a previous installer skipped the uncoupling layer entirely – all things worth fixing before the new cabinets and countertop go in.
Which Schluter Models This Applies To
Schluter is a manufacturer of tile-installation systems and accessories, not a single product – the most common in kitchen work are Ditra and Ditra-XL uncoupling membranes, Kerdi waterproofing membrane, Kerdi-Board and Kerdi-Band, Schluter-Trim and -Stair profiles, and the Schluter line of substrates. Identifying the right system starts with the membrane: Ditra is a thinnest-pattern polyethylene mat with dovetail-mortar cavities; Ditra-XL is taller and used where a higher build-up is acceptable. Check the printed lamination on the roll edge if it’s still visible – that names the product and lot. Kerdi-Board carries a recognizable orange fleece face; Kerdi-Band has a preformed inner edge and is cut at the seams. When the original packaging is gone, we can determine suitability by thickness, fleece color, and how the piece seats under a tile edge – there’s no lookup table, so a qualified installer makes the call. Schluter does not sell to the public through a retail van; the system is sourced through tile distributors and dealer networks, and the version of the system matters more than the brand stamp. We are an independent service provider and are not affiliated with Schluter – we set the project up to accept the correct Schluter system and can source the pieces once the job is scoped.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Kitchen Remodeling Is Failing
Membrane and substrate failures mostly announce themselves the same few ways in Arlington kitchens:
- Cracked grout lines across a tile field. This usually means the uncoupling layer was omitted, laid with too little mortar, or installed over a subfloor that moves – the tile has nowhere to flex.
- Hollow or drumming tiles underfoot. An air void under mortar means the Ditra or Kerdi never fully seated; you’ll hear it with a light tap and it gets worse as traffic continues.
- Lifted corner of Kerdi at a seam or curb. A poorly bonded overlap lets moisture track behind the membrane, and in a wet-area kitchen that shows up as a soft spot or a stain at the baseboard.
- Water staining at the toe-kick or behind the dishwasher. Kerdi or Kerdi-Band installed with too thin a thinset layer lets water bypass the system instead of draining to the waterproofed layer.
- Cracked Schluter trim profile or a loose end cap. A profile that’s split or has shifted off its tile edge is a finish failure, not a structural one, but it signals the substrate beneath may have moved too.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Arlington, the full kitchen remodel range runs $14,000 – $45,000, depending mostly on cabinet and countertop scope rather than the membrane. Small kitchen remodels run $9,000 – $20,000. Cabinet installation is $4,000 – $13,000, countertops $2,000 – $6,500, and backsplash work $800 – $2,500. If a kitchen island is being added or reinstalled with the floor, that’s $3,000 – $10,000. Labor for the membrane itself is a small slice of these totals – usually a few hundred dollars at most – but the range moves with how much tile is being replaced, whether the old floor must come up, and whether the subfloor needs flattening. Every project gets a written scope and written change orders before any scope shifts. We pull permits and pass inspections on every eligible job. All work is backed by our 90-Day Done Right Promise.
DIY or Call Us?
An owner can safely check tile by tapping it lightly, look for visible membrane lifting at seams or edges, and inspect under-cabinet edges for water staining. What we don’t advise DIYing is the installation itself: uncoupling membrane and waterproofing depend on the right thinset, correct overlap, and correct curing, and getting any of those wrong traps water or leaves the tile field undoing itself in six months. If a subfloor needs flattening or a wet-area membrane has failed, that’s a job for a trained installer, not a weekend patch. We’d rather have you call before a small repair turns into a full floor redo. Call (888) 590-9867 for a free estimate.
FAQs
How long does Schluter membrane last in an Arlington kitchen? A properly installed Schluter uncoupling or waterproofing membrane is a long-life component, and in a typical indoor kitchen it will last as long as the tile above it. The failure timeline in Arlington is driven by sun exposure and heat at any exterior-facing wall, moisture at the dishwasher and sink, and subfloor movement – those are what pull the lifespan down, not the membrane itself.
Can the existing membrane be repaired rather than replaced? Sometimes. If a single corner of Kerdi-Band has lifted at a wet seam, a qualified installer can often remove the affected tile, re-bond the band, and re-tile the area. Cracks running across a tile field usually mean the whole floor is coming up – patching over a moving substrate only hides the problem.
How long does a membrane swap take? A small seam or corner repair is typically a one- or two-day job, with cure time before tile is re-set. A full floor rebuild in an Arlington kitchen with cabinet re-install and new counters runs several days to a couple of weeks depending on cabinet lead time. You’ll get the schedule in writing before we start.
How do you source the Schluter part? We don’t stock Schluter parts and we don’t carry them on a truck – we order the correct system from tile distributors and dealer networks after we’ve inspected and scoped the job, so you get the right model, not whatever’s on the shelf. That also lets us match the membrane to the tile size and subfloor rather than guess. Call (888) 590-9867 for an exact quote – estimates are free.
If you’re ready to look at your kitchen, we’ll come out, check the membrane and substrate, and give you a written estimate backed by our published prices and our 90-Day Done Right Promise. We also install and service KraftMaid, Cambria, and Silestone in Arlington kitchens. Call (888) 590-9867 for a free estimate.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.