Roofing
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Roofing: The Arlington Owner’s Guide
We install and repair Schluter roofing systems in Arlington, and most homeowners call us when water is showing up where it shouldn’t. The parts themselves are affordable – most individual Schluter components run $40 to $180 – so the real cost is labor and getting the right profile matched to your deck. We can usually get eyes on a failing Schluter flashing or transition strip within a day or two of your call.
Owners tend to discover the problem the same way: a brown ring on the ceiling under a valley, granules washing into the gutter, or a drip that only shows up during a hard north Texas downpour. By the time you see water inside, the Schluter membrane beneath has usually been compromised for one or two seasons. Arlington’s freeze-thaw swings in February and March are hard on the adhesive bonds, and hail – which we get plenty of between April and June – punishes the surface layer first.
Which Schluter Models This Applies To
Schluter covers several roofing product lines, and the part you need depends heavily on which system was installed. Their KERDI line is the waterproofing and uncoupling membrane most common on Arlington roofs that have flat or low-slope sections over porches and additions. The SCHIENE and RONDEC profiles are edge-trim pieces used at roof-to-wall transitions and drip edges. If you’re not sure what you have, look at the original installer’s paperwork or pull back a shingle tab to find the printed backing. Schluter prints the product name directly on the membrane and the profile packaging – measure the width of your trim piece and compare to their published dimensions, since a quarter-inch misfit means water tracks behind the flashing instead of away.
We are an independent contractor, not affiliated with Schluter, so we can tell you plainly: their OEM parts are the safe match when your system is under warranty or still new. Aftermarket equivalents exist and cost 20 to 40 percent less, and for an older install past warranty they’re often a reasonable call. The decision comes down to whether the rest of the system has life left in it.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Roofing Is Failing
Here’s what we look for on Arlington roofs, and what each symptom usually means:
- Water stains on the ceiling or at a roof-to-wall joint. The membrane bond has lifted and water is tracking behind the Schluter profile instead of over it. In our climate the bond often fails at the vertical run, not the horizontal.
- Loose or lifting edge trim. The fastener heads have backed out or the sealant around the SCHIENE profile has cracked. Arlington’s summer heat – real 100-degree stretches – softens sealant faster than most homeowners expect.
- Granule loss concentrated near the transitions. This points to abrasion where the Schluter trim sits proud of the shingle plane. A part that’s slightly too tall catches wind-driven rain and wears the shingle edge.
- Visible cracks or brittleness in the membrane. Usually from UV exposure after the surface layer failed. Once the membrane cracks, it’s no longer waterproof, and a patch won’t hold.
- Recurring leaks after a prior repair. Often the original part was the wrong size for the slope. A profile sized for a shallow pitch won’t perform on a steeper Arlington roof, so it fails again every season.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Arlington, most Schluter roofing repairs land between $400 and $1,800 installed, and a full replacement where the whole membrane and trim system is redone runs $8,000 to $20,000 depending on square footage and roof complexity. The repair range reflects the piece itself plus labor to open the roof, set the new part, and seal the transition. The replacement range is driven by deck condition, how many roof-to-wall transitions you have, and whether valley work is involved.
We put every part on the quote by name and price. If we open the roof and find rot under the deck, that change arrives as a written change order before we continue – no surprise invoice at the end. Parts and labor are both itemized so you can see exactly what the piece cost versus the install. Every eligible job includes permits pulled and inspections signed, and the work comes with our 90-Day Done Right Promise in writing. We also install KraftMaid, Cambria, and Silestone if you’re doing other work at the same time.
DIY or Call Us?
You can safely check a few things yourself: look at the ceiling and attic for stains, feel the trim edges for lifting with a gloved hand, and snap photos of the part so we can identify it before we come out. Measuring the trim width is also fine and saves a trip.
What we’d steer you away from is opening the roof to swap the membrane or profile on your own. Roof work at height is where experienced hands matter most – a slip on a wet Arlington roof after a rain is a serious fall, and re-sealing a Schluter transition wrong means the leak returns within a season. This isn’t a faucet washer. If the part needs replacing, call (888) 590-9867 and we’ll take a look. Estimates are free.
FAQs
A properly installed Schluter membrane system typically lasts 20 to 30 years, but the exposed trim and flashing are the first to wear in Texas conditions – expect the edge profiles to need attention around year 12 to 18, especially on roofs that take full afternoon sun. Hail years shorten that. Call (888) 590-9867 if you’re unsure of your roof’s age.
Yes, in most cases an individual Schluter part can be replaced without redoing the whole system, provided the membrane beneath is still intact. If we find the membrane has cracked or lost its bond across a wide area, a spot repair won’t hold and we’ll tell you straight. Call (888) 590-9867 for a free second opinion on any written estimate.
A single Schluter profile or flashing replacement is usually a half-day to a full day, weather permitting. A larger membrane and trim replacement across multiple transitions runs two to three days. We schedule around dry weather – sealing a transition before a rain front moves through is asking for a callback.
We order the OEM Schluter part matched to your system by product name and measured dimension, and we confirm the profile size before the order goes out. We don’t carry parts on a truck, so the part arrives specifically for your job. If an aftermarket equivalent makes sense for an older out-of-warranty install, we’ll price both and let you decide.
If water is getting in and you’re not sure which Schluter part you have, call Barrett & Sons Construction Arlington at (888) 590-9867 to schedule your free estimate. We pull permits, put every change in writing, and Tom’s crew stands behind the work with the 90-Day Done Right Promise.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.