A Barrett company - serving Arlington, TX

Schluter Windows & Doors in Arlington, TX

Windows & doorsWindows & doors
Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Schluter Windows & Doors: The Arlington Owner’s Guide

If you have a failing Schluter window or door component, we can install the correct replacement part for you in Arlington, and installed pricing for the related window and door work typically lands between $4,500 – $15,000 for standard window replacement and $8,000 – $25,000 for impact-rated units, with a written quote before anything is ordered. We’re an independent service provider, not affiliated with Schluter, so we match your exact model number to the right part rather than guessing. Most Arlington owners discover the failure the same way: a draft they didn’t have last winter, a door that won’t latch square, or storm water showing up on the sill after a hard spring rain.

Call (888) 590-9867

Schluter is best known for tile-edge profiles and waterproofing systems, but their window and door line covers sills, thresholds, and drainage profiles that resolve the transition between exterior openings and finished surfaces. When those pieces crack, lift, or stop shedding water, you don’t get a dramatic failure. You get slow moisture intrusion and a threshold that rattles underfoot.

Key Takeaways:

  • Bring us the model number or a clear photo of the profile cross-section; that’s faster than describing it.
  • Texas sun and clay soil movement drive most Schluter threshold and sill failures in Arlington.
  • We pull permits on every eligible job and back all work with the written 90-Day Done Right Promise.

Which Schluter Models This Applies To

Schluter’s window and door components show up most often in the KERDI family and their associated threshold and sill profiles, plus the SCHIENE and RENO transition profiles used where a finished floor meets a door opening. The tricky part is that profile names repeat across sizes, so the stamped part number on the profile itself (usually on the anchoring leg) is what actually identifies your unit. A 5/16-inch and a 3/8-inch profile look nearly identical in a photo. Measure the exposed height and the anchoring leg width before you call, or the wrong part shows up.

The OEM-versus-aftermarket call matters here. Schluter’s own profiles are matched to their waterproofing membranes and are worth buying when the assembly is still intact and you’re replacing one piece. Aftermarket extruded aluminum equivalents cost less, but the dimensions run a hair off, and in Arlington a profile that’s 1/16-inch proud of the tile creates a lip that catches water. On a full door or window replacement rather than a profile swap, we work with Andersen and Marvin units, and we also handle KraftMaid, Cambria, and Silestone on interior finish work around the opening.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Schluter Windows & Doors Is Failing

  • Water pooling on the sill after rain. The drainage channel in the sill profile is clogged or the profile has separated from the membrane, so water sits instead of shedding. Left alone, that moisture gets behind the finished wall.
  • A threshold that lifts or rocks underfoot. The anchoring leg has lost its bond, usually from thermal cycling. North Texas swings from 105 in August to the teens in a January cold snap, and that expansion and contraction works fasteners and adhesive loose.
  • Cracks in the profile or grout line at the opening. Ground movement in Arlington’s expansive clay soils flexes the frame, and a rigid profile cracks rather than flexing with it. Hairline cracks here are the first sign water will follow.
  • A draft you can feel at the bottom corner of the door. The threshold profile has worn or the door has dropped, breaking the seal line. This one costs you money every month on the electric bill, not just comfort.
  • Mold or dark staining on the interior trim near the opening. That’s moisture that got past a failed sill profile and is now trapped. It’s the symptom owners call us about last, and it’s the one that means interior repair too.

Replacement Cost & What’s Included

Honest installed pricing for Arlington, and what drives it:

Work Typical Installed Range
Window replacement (standard) $4,500 – $15,000
Impact window installation $8,000 – $25,000
Profile or threshold component swap Quoted line-item, usually the low end of the scale

The range comes down to unit count, opening size, whether the frame is square, and how much interior finish has to come out to reach the failed profile. Every quote is a written line-item, so you see parts cost and labor cost separated. Price changes only arrive as a written change order before the work happens. Every eligible job gets permits pulled and inspections signed, and the whole thing is covered by the 90-Day Done Right Promise. If it’s not right, Tom comes back.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

DIY or Call Us?

You can safely do a few things. Look for the part number, measure the exposed profile height and anchoring leg width, take a photo of the cross-section, and check for visible cracks or a lifted threshold. That’s inspection, not repair, and it tells you what you’re dealing with.

Where DIY goes wrong is removal. Pulling a sill or threshold profile that’s bonded to a waterproofing membrane usually tears the membrane, and then you’ve traded a $40 part for a water intrusion problem that runs hundreds to fix. And anything above the first floor, or any door that could fall out of square while you’re working, should be handled by trained crew members. If you’re not sure, call us at (888) 590-9867 before you start prying. Estimates are free.

FAQs

How long do Schluter window and door profiles last in Arlington? Plan on 10 to 15 years for a well-installed profile in this climate, and expect the shorter end on a south-facing door that takes full afternoon sun. UV exposure and clay-soil movement are the two things that shorten lifespan here, and a profile that’s shedding water properly lasts noticeably longer than one that’s been clogged.

Can a failed profile be repaired instead of replaced? Sometimes, yes, if the waterproofing membrane behind it is still intact and only the profile has cracked or lifted. If the membrane is compromised, replacement is the honest answer. We look at both before quoting and tell you which one you actually need. Call (888) 590-9867 for a free second opinion on any written estimate you’ve already received.

How long does the swap take? A single profile or threshold component typically takes a few hours. A full window or door replacement runs a day or more per opening depending on size and finish work. We schedule around your calendar, not ours, and give you the realistic timeline in writing before we start.

How do you source the right Schluter part for my door or window? We use the stamped part number and your measurements, not a visual match, because profile names repeat across sizes and a wrong-sized part fails the same way within a season. In Arlington, we order the exact component rather than substituting a different brand’s equivalent. If the OEM piece is discontinued, we tell you before we proceed rather than slipping in an aftermarket substitute.

Get a Written Estimate

If you’ve got a Schluter component that’s cracked, lifting, or letting water in, the fastest way to know where you stand is a look at it. Barrett & Sons Construction Arlington sends out crew members who know these assemblies, quotes the work in writing line by line, and only starts once you’ve read it. Call (888) 590-9867 for a free estimate. We’ll take a look, tell you what actually failed, and give you a number you can plan around.

Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.

Need Construction help nationwide? Licensed & insured · free written estimates
Call (888) 590-9867
Local Service Coverage

Request a Free Estimate in Arlington

Tell us what you need - Barrett & Sons Construction Arlington responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Call Now - 24/7 Dispatch