Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Fence Installation: The Arlington Owner’s Guide
We handle fence installation in Arlington using Schluter-compatible systems and hardware, and most of our Arlington fence installs land between $3,500 and $9,000 installed, depending on linear footage and material. We quote the full job in writing before anyone touches your yard, so there’s no surprise invoice waiting at the end.
A failing fence part usually announces itself slowly. Posts start leaning after a hard rain. Hardware that ran fine last spring won’t line up by August. A gate that used to shut with one hand starts dragging on the concrete. That’s when most owners start hunting through their paperwork for the exact model number, because the part they’re staring at isn’t the part that fits.
Which Schluter Models This Applies To
Schluter parts don’t cross-number the way people hope. The model stamped on your gate hardware or connector block ties to a specific lineup, and the part that fits a 4-inch post won’t seat on a 5-inch one no matter how close the measurements look. Before you order, find the label on the original part. Take two photos, one of the label and one of the part installed. If the label has worn off, measure the post and the connector bracket with a tape and write both numbers down. That pair of numbers is what identifies your part, not just the brand name.
When it comes to OEM versus aftermarket, the decision is straightforward. On high-stress fence parts, hardware and connectors, matched OEM repairs hold up through Texas heat cycles better than generic replacements. Lighter-duty accessories are fine with a quality aftermarket equivalent, and we’ll tell you which side of that line your part falls on. We don’t stock parts and we don’t carry inventory on a truck. We source what fits your exact model and add it to the written scope so you know the line item before you commit. We’re an independent installer serving Arlington, not a Schluter dealer or affiliate.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Fence Installation Is Failing
- Gate sagging at the hinge side. A worn connector or anchor plate lets the gate drop, so the latch stops meeting the strike. Left alone, the sag puts stress on the post itself.
- Leaning posts after rain. You’re not just fighting wet soil, you’re fighting a hardware anchor that’s losing grip in it. Replacing the part on a compromised footing means it fails again in a season.
- Rust streaks on hardware. Any defect in the finish invites it, and the corrosion spreads at joints where moisture sits.
- Gaps that won’t stay fixed. Loose or worn hardware lets sections drift. If you tighten and the gap returns within weeks, the connector itself is failing.
- Cracks at attachment points. Hairline cracks where the part meets the post or rail mean the material is under too much load. It may be a mismatched part or a tired original.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Fence installation work in Arlington, including replacement and upgrade jobs, generally runs $3,500 to $9,000 installed. The range moves on linear feet, post count, existing removal, footing condition, and whether you’re replacing hardware and connectors or the whole structure. A run at the lower end is simpler in both size and hardware; a full property line with solid panels and custom hardware sits near the top.
What drives most of the gap is site condition. Northeast Tarrant County soil expands fast after heavy spring rain and dries hard in July, which shifts footing and stresses hardware constantly. That’s why we bake footing scope into the quote up front. Original parts from the manufacturer run higher than quality aftermarket equivalents, and we list each one as its own line. Every job we do is backed by our 90-Day Done Right Promise, written into the contract, so if something’s off we come back and make it right.
DIY or Call Us?
Some of this you can check yourself. You can inspect for rust, measure the gap, photograph the label, and tighten exposed fasteners. Where it goes wrong is resetting footings and lifting panels. Setting a post correctly requires the right depth, the right concrete mix, and the right plumb before the concrete sets, and in Arlington that second part matters because the soil around it moves. A footing set an inch out of plumb will pull the whole run out of line once the panels go on. Pulling fence panels solo is also harder than it looks, and a dropped panel can crack the part you just bought. If your hardware failure traces back to a footing problem, that’s the moment to call us at (888) 590-9867. We’ll take a look and quote it in writing, free.
FAQs
How long does a Schluter fence installation last? Installed over stable footings, most setups last 15 to 20 years with basic upkeep. In Arlington, the wet-dry swings are the biggest wear factor, so footing condition and hardware grade matter more than a lifespan chart from the manufacturer’s website. Call (888) 590-9867 if you want our read on yours.
Can it be repaired instead of replaced? Yes, a single hardware part or connector can usually be swapped without replacing the full fence, if the footing and posts are sound. We diagnose what failed first, then quote a repair or replacement in writing so you’re not guessing. Calling us costs you nothing.
How long does the part swap take? Replacing one connector or gate hardware set is typically a short job, often a few hours to most of a day, depending on how easy your gate is to access. A full run with new footings is quoted in days, not hours. We’ll give you the real timeline in your written scope before we start.
How do you source the part? We match your model number and the measurements you provide to a stocked supplier part, then show the line item in your written quote. We don’t claim to carry parts on a truck or keep them in inventory. If your model’s part is discontinued, we’ll tell you what fits instead, in plain terms, before you approve anything. We also install KraftMaid, Cambria, and Silestone fixtures elsewhere in the home, and we apply the same sourcing discipline to all of them.
Fence repairs and installs aren’t the kind of work you want to figure out twice. Get a second opinion on any written estimate, free of charge. We also take $40 off any repair over $200, no trip charge inside the county, and offer a 10% Senior & Veteran discount on every visit. Call (888) 590-9867 for a free estimate.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.