A Barrett company - serving Arlington, TX

Schluter Driveway & Pavers in Arlington, TX

Driveway & paversDriveway & pavers
Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Windows & doorsWindows & doors
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Schluter Driveway & Pavers: The Arlington Owner’s Guide

We install Schluter-compatible driveway and paver assemblies across Arlington, and most full driveway replacements run $7,000 – $18,000 depending on square footage and base prep. If a Schluter component has failed under an existing drive, we can often match and swap the piece without tearing out the whole slab, and we quote that work same week. Most Arlington owners find out something’s wrong the same way: a paver beside the driveway tips underfoot after a rain, or water starts pooling against the garage slab instead of running to the street. That’s usually the edge restraint or the drainage profile giving up, not the pavers themselves.

Call (888) 590-9867

Which Schluter Models This Applies To

Schluter makes several driveway-adjacent assemblies, and matching the right piece matters more than most owners expect. Their paver and terrace lines center on the TREP-E and TREP-G edge profiles, the TROBA drainage mats, and the KERDI-DRAIN line for transitions where a drive meets a walk or patio. Each family comes in fixed heights and widths, and a TREP-E sized for 2 3/8-inch pavers won’t accept a 2 3/4-inch stone no matter how you shim it. Check the profile height stamped on the metal before you order anything.

You can usually ID what’s under your drive by pulling one paver at the edge and reading the profile lip. If the label is gone, measure the paver thickness and the reveal depth; those two numbers narrow it to one or two compatible pieces. On the OEM-versus-aftermarket call, we lean OEM on Schluter edge profiles, because the stainless grade and the anchoring leg geometry are what keep the edge from walking out under a Texas freeze-thaw cycle. A cheaper equivalent may fit the slot and fail in three winters. We’re not affiliated with Schluter; we’re an independent installer who knows these assemblies and installs them by the book.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Schluter Driveway & Pavers Is Failing

  • Pavers shifting or rocking at the edge. The edge profile has lost its anchor or bent out of true, so nothing is holding the field pavers in a straight line.
  • Water pooling against the garage or house. The drainage mat or slope transition has clogged or settled, and water is finding the low spot instead of the street.
  • Rust streaks on pavers or the slab. A lower-grade profile is corroding at the anchor holes, which is common after a decade of North Texas runoff and road salt.
  • A gap opening between the drive and the walk or patio. The transition channel has dropped or separated, letting soil and water work underneath.
  • Loose sand or gravel washing out at the edge. The bedding layer is migrating because the containment profile no longer holds it.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

For Arlington, a targeted edge profile or drainage transition swap typically lands in the $250 – $700 range as part of a broader driveway sealing or repair visit, while a full paver driveway replacement runs $7,000 – $18,000. The range is driven by linear footage of profile, whether the base underneath needs re-grading, and how many pavers have to come up to reach the failed piece. What you’ll get from us is simple: the part and the labor on one written line, not a mystery invoice at the end. Every price change arrives as a written change order before we start, and the repair is backed by our 90-Day Done Right Promise. That written promise means if the edge fails again inside that window, one call brings Tom back.

DIY or Call Us?

Some of this you can check safely. Walk the edge of the drive after a rain and mark where water pools, and lift one perimeter paver by hand to read the profile lip and measure thickness. Where DIY goes wrong is under the surface: resetting a profile without re-compacting the base means it’ll walk out again within a season, and prying a bonded profile loose can crack the adjoining pavers and open the bedding to more water. None of that is dangerous the way a garage spring is, but it’s the kind of job where doing it twice costs more than doing it once. If you’d rather not gamble on the base prep, call (888) 590-9867 and we’ll quote it same week.

FAQs

How long does a Schluter edge profile or drainage transition last in Arlington? A properly installed stainless Schluter profile should hold 15 to 25 years under normal North Texas weather, but DFW summer heat cycling and winter freezes punish any profile that wasn’t set on a compacted, correctly graded base. If you’re under 10 years and already seeing movement, the base prep is the suspect, not the product.

Can a failing profile be repaired instead of replaced? Often yes. If the stainless is intact and only the anchor or bedding has failed, we can reset it and re-seat the pavers without a full teardown. Call (888) 590-9867 for a free second opinion on any written estimate, and we’ll tell you honestly whether it’s a repair or a replacement.

How long does the swap take? A single edge or transition section usually goes in one day once we have the right piece. A full-length replacement along a two-car drive is typically two to three days including base work.

How do you source the Schluter part? We match your existing profile by height and width, order the correct OEM piece, and confirm fit against your paver thickness before we touch the drive. You’ll see the exact part on the quote, not a generic “materials” line.

Barrett & Sons Construction is an owner-operated Arlington contractor, founded in 1998, and we also install leading brands like KraftMaid, Cambria, and Silestone on the interior side. Tom Barrett’s name, address, and license number are published and verifiable; look them up before you sign anything. When you’re ready to price the work, call (888) 590-9867 for a free estimate.

Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.

Need Construction help nationwide? Licensed & insured · free written estimates
Call (888) 590-9867
Local Service Coverage

Request a Free Estimate in Arlington

Tell us what you need - Barrett & Sons Construction Arlington responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Call Now - 24/7 Dispatch