Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Sterling Fence Installation: The Arlington Owner’s Guide
Barrett & Sons Construction Arlington installs Sterling fence systems across Arlington, with typical installed pricing between $3,500 and $9,000 depending on fence run, material, and gate count. We schedule estimates within a few days of your call, and we’re not affiliated with Sterling itself – we’re an independent installer who knows their product line well. Most Arlington homeowners start this search the same way: a post has started leaning after a heavy rain, a gate drags on the ground, or a panel is bowing, and they want to know whether it’s a repair, a replacement, or something bigger going on underground.
Key Takeaways
- Sterling fence installation in Arlington runs $3,500 – $9,000 installed, with the range driven by linear feet, material, and gates.
- We’re an independent installer, not a Sterling dealer or affiliate.
- Texas clay soil and summer heat are the two biggest reasons Arlington fences fail early.
- Every price change arrives as a written change order before work starts.
Which Sterling Models This Applies To
Sterling builds fencing in several lines, and the differences matter when you’re matching parts or planning a repair. Their vinyl privacy and picket systems are the most common in Arlington neighborhoods, with aluminum and ornamental steel lines showing up more on commercial corners and HOA-fronted lots. Identifying yours starts with a look at the post cap or the inside face of a rail – Sterling typically stamps or labels the profile there. If the label has faded, measure the rail width and post dimension; those two numbers will tell an experienced installer which series you’re working with.
On the OEM-versus-aftermarket question, here’s the honest answer: for posts, rails, and pickets, a quality aftermarket equivalent will hold up just as well as Sterling’s own parts, often at a lower price, because the profiles are standardized. Where OEM makes more sense is on proprietary caps, brackets, and gate hardware – aftermarket versions sometimes fit loosely and rattle in the wind. Our crews have up to 28 years of experience between them, and we’ve replaced enough fence components in Arlington to know which parts to source OEM and which to source from a trusted supplier. We’ll tell you which is which on your specific fence.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Sterling Fence Installation Is Failing
- Posts leaning or rotating after rain. Arlington’s clay-heavy soil swells when wet and shrinks when dry, and a post set in a shallow hole without proper concrete depth will move with it. This is the most common failure we see after a wet spring.
- Gate sagging or dragging on the ground. Usually a hinge or gate frame issue rather than the post itself, though sometimes a stressed post is the cause. Worth checking both before assuming the gate is shot.
- Loose or popped pickets and rails. On vinyl, this usually means a hidden fastener has cracked from heat expansion, which is common in Arlington’s 100-degree summers. On aluminum or steel, it’s often a fastener that wasn’t torqued properly on the original install.
- Rust streaks or discoloration on metal components. Galvanized or powder-coated hardware failing earlier than expected, usually because the coating was scratched during installation and never touched up.
- Panels bowing or sagging between posts. Often a sign of rails that were undersized for the span, or post spacing that pushed past what the material can handle. This one usually points to a full section replacement rather than a spot repair.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Sterling fence installation in Arlington lands in the $3,500 – $9,000 range for most residential runs. A short privacy fence with one gate sits near the low end; a longer perimeter with multiple gates and a mix of materials pushes toward the top. Line-item pricing looks roughly like this:
| Item | Typical Range (Arlington) |
|---|---|
| Vinyl fence, installed | $3,500 – $9,000 |
| Aluminum fence, installed | $4,000 – $10,000 |
| Post replacement, per post | Quoted after site inspection |
| Gate hardware replacement | Quoted after site inspection |
| Full section replacement | Quoted after site inspection |
What drives the number up: linear feet, material choice, gate count, and whether your posts need to be reset in concrete (common in older Arlington yards). What we include: hauling off the old fence, setting posts to proper depth, and inspecting and signing off on any permitting Arlington requires for your lot. Every completed job is backed by our 90-Day Done Right Promise. If something isn’t right, one call brings Tom back out.
DIY or Call Us?
Some fence work is genuinely doable on your own: swapping a gate hinge, replacing a cracked picket cap, touching up a rust spot on a steel post. Those are quick fixes that don’t require special tools or a permit.
Where it goes wrong is post setting and full section replacement. A post that isn’t set to the right depth and concrete weight in Arlington’s clay soil will lean within a season – we’ve re-set posts that were installed exactly that way a year before. And digging near an existing fence line means finding gas, water, and utility lines the hard way if nobody called 811 first. We pull permits and call for locates before we dig, every time, and that’s not something most homeowners want to handle solo. If you’re not sure whether your issue is a quick fix or a full replacement, call (888) 590-9867 and we’ll tell you straight, even if the answer is “you can handle that one yourself.”
FAQs
A well-installed Sterling vinyl or aluminum fence typically holds up 15 to 20 years in Arlington’s climate, though heat expansion and clay soil movement are the two things that shorten that. Post depth and proper concrete setting are the biggest factor in whether you get the full lifespan.
Often yes. Individual pickets, rails, gate hardware, and even single posts can usually be swapped without replacing the whole run. If multiple sections are bowing or more than two posts are leaning, a partial replacement usually makes more financial sense than a repair.
A single post or gate hardware replacement takes a few hours. A full residential fence installation in Arlington usually runs one to three days depending on linear feet and gate count, weather permitting.
We source Sterling-compatible components through suppliers we’ve worked with for years, and we’ll tell you upfront whether OEM or a quality aftermarket equivalent is the right call for your specific fence. We don’t stock parts or carry inventory – every part is matched to your fence before we order it. Call (888) 590-9867 for a free estimate.
When you’re ready to get a real number for your Sterling fence, call (888) 590-9867 to schedule your free estimate. We also install and service KraftMaid, Cambria, and Silestone products on other jobs, and published standing offers include $40 Off Any Repair Over $200, a Free Second Opinion on Any Written Estimate, No Trip Charge Inside the County, and a permanent 10% Senior & Veteran discount.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.