Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Owens Corning Fence Installation: The Arlington Owner’s Guide
Owens Corning fiberglass composite fence systems installed in Arlington typically run $3,500 to $9,000 for a standard residential run, depending on linear footage, gate count, and grade changes on your lot. We install and repair Owens Corning-compatible fence systems across Arlington, and most straightforward runs are wrapped up in two to three working days once materials are on site. Call (888) 590-9867 for a free written estimate.
Most Arlington owners don’t set out to buy a fence. They discover a problem first. A post feels soft when you lean on it after a spring storm rolls through. A gate that latched clean last fall sags and drags on the concrete. Or a stretch of panel along the property line has gone chalky and gray while the rest still looks fine. That last one is common here: Owens Corning composite fence products are engineered for moisture and termite resistance, but North Texas sun and our shrink-swell clay soils test them in ways the spec sheet won’t tell you about. The fence didn’t fail overnight. It failed slowly, and now you’re deciding whether to repair a section or replace the run.
Which Owens Corning Models This Applies To
Owens Corning’s fence line falls under their composite and fiberglass fencing products, sold through building material dealers rather than direct to homeowners. The product you’ll most often encounter is their composite privacy fencing system, which uses interlocking pickets and reinforced posts rather than traditional nail-through assembly. If your fence was installed in the last decade or so and has a clean, uniform panel look without visible fasteners on the picket face, there’s a good chance it’s this system.
Identifying your specific model matters before you order anything. Check three places: the inside face of a gate post for a manufacturer label or stamped production code, the post cap for a molded part number, and any original installation paperwork tucked in your closing documents. If none of that survives, measure the picket width, the gap between pickets, and the post spacing center to center. Those three numbers narrow the field fast. Bring them to us and we’ll match them against the current Owens Corning catalog.
On the OEM-versus-aftermarket question: for structural components (posts, rails, gate hardware) we recommend staying with Owens Corning-spec parts, because the interlocking geometry is proprietary and a generic rail won’t seat correctly. For pickets and caps, quality aftermarket equivalents exist and can save 15 to 25 percent, but only if the dimensions and color match your existing run. Mixing brands mid-fence shows up as a visible color shift within two summers. Barrett & Sons Construction Arlington is an independent installer and not affiliated with Owens Corning; we source genuine parts through authorized dealers and tell you plainly when an aftermarket part is the smarter buy.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Owens Corning Fence Installation Is Failing
Here’s what we actually see on Arlington properties, and what’s usually behind it:
- Posts that wobble or lean after rain. The post hole wasn’t set deep enough for our clay soil, or the concrete collar cracked and let water in. Once a post moves, the panels rack and the whole run carries stress it wasn’t designed for.
- Chalking, fading, or gray patches on one side of the fence. Our UV load is brutal, and south- and west-facing panels take the worst of it. Some fading is normal over a decade; patchy graying usually means the panel is a lower-grade replacement someone slipped in during an earlier repair.
- Sagging gates that drag or won’t latch. Gate hardware is the first thing to go. Hinges loosen, the gate frame racks, and the latch strikes wrong. Left alone, a dragging gate tears up the post it’s hung on.
- Cracked or split pickets near the ground line. Standing water at the base after a storm, plus soil movement, puts stress on the lowest picket. A single split is a repair; a line of them means the bottom rail has failed.
- Panels separating at the seams. Wind load on a long run with too few posts, or rails that were never fastened to spec. This one gets worse fast in spring storm season.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For an Owens Corning-compatible fence install or section replacement in Arlington, expect $3,500 to $9,000 for a typical residential run. The range is driven by linear footage, post count and depth (our clay demands deeper holes than coastal markets), gate count, and whether we’re matching an existing color run or installing all new.
Here’s what a written estimate from us looks like, line by line:
- Materials (posts, rails, pickets, caps, hardware) priced individually
- Post hole excavation and concrete setting
- Removal and disposal of the old fence, if applicable
- Gate framing and hardware installation
- Labor, permits if required by the city, and final cleanup
Every price change comes to you as a written change order before a single post goes in the ground, so there are no surprise invoices at the end. Every eligible job gets permits pulled and inspections signed. And every completed fence is backed by our written 90-Day Done Right Promise: if something isn’t right, one call brings us back. Our crew members have up to 28 years of experience, and we also install premium brands across other trades, including KraftMaid, Cambria, and Silestone for interior work.
DIY or Call Us?
What you can safely check yourself: walk the run and push on each post, look for cracks at the base of pickets, test every gate latch, and photograph any graying or separation. Measure your post spacing and picket width. That’s the information we need to quote you accurately, and you can gather it in fifteen minutes with a tape measure and a phone.
Where DIY goes wrong: setting posts in our clay. A post hole that’s too shallow or a concrete mix that’s too dry looks fine for one season and then leans after the first hard rain. Gate framing is the other trap. A gate hung without proper diagonal bracing racks within months, and fixing it means pulling the whole assembly. And if you’re replacing structural rails on a proprietary Owens Corning system, generic parts won’t seat, and you’ll be drilling holes that void the panel warranty. This isn’t a weekend job for most homeowners, and that’s fine. Not every job should be one.
Call (888) 590-9867 and we’ll walk your property, measure what matters, and hand you a written estimate with every line itemized. A live person answers the phone 24/7, and there’s no trip charge inside the county.
FAQs
Expect 20 to 30 years for the panels and pickets under normal conditions, with posts and hardware being the first items to need attention, often in the 10 to 15 year range. Our UV exposure and clay soil movement are the two factors that shorten that window, which is why post depth and drainage matter more here than the marketing literature suggests.
Usually, yes. If the posts are solid and only a few pickets or one gate failed, a section repair runs a fraction of a full replacement. If three or more posts are moving, the run has lost its structural integrity and patching it just delays the inevitable. We’ll tell you honestly which situation you’re in. Call (888) 590-9867 for an exact quote; estimates are free.
A single section repair typically takes half a day to a full day. A full run replacement runs two to three working days for most Arlington properties, weather permitting. We schedule around your availability and clean up the site each day before we leave.
We order through authorized building material dealers and match your existing model using the label, part number, or measurements from your fence. We don’t claim to keep parts on hand or on a truck, so lead time depends on dealer availability, usually a week or two for standard components. We’ll confirm the timeline in your written estimate before you commit. Call (888) 590-9867 for your free estimate.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.