A Barrett company - serving Arlington, TX

Owens Corning Home Additions & ADU in Arlington, TX

Home additions & ADUHome additions & ADU
Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
RoofingRoofing
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Owens Corning Home Additions & ADU: The Arlington Owner’s Guide

We build Owens Corning home additions and ADUs in Arlington at a typical installed cost of $45,000 to $130,000 for an addition and $90,000 to $220,000 for a full ADU, and the Owens Corning envelope components in that scope (foam board, sheathing tape, shingles, loose-fill insulation) are matched to your build and specified in writing before we start. You’re likely here because something in that envelope has already failed. Maybe a corner of the addition feels soft underfoot. Maybe the shingle field over the new roofline is lifting at the edges. Or you’ve found a wet stain on the ceiling under a foam-sheathed bump-out and you’re trying to work out which Owens Corning piece is the culprit.

Call (888) 590-9867

Before anything else: we’re an independent local contractor, not affiliated with Owens Corning. We install and repair their materials, we don’t make or sell them, and we don’t claim a warehouse of parts. What we can do is tell you which part your build takes, what it costs in Arlington, and what happens when it goes on wrong.

Key Takeaways

  • Owens Corning parts aren’t universal. Foam R-value, sheathing tape grade, and shingle series all have to match the specified assembly.
  • Adhesives and foam don’t do well in Texas heat if they aren’t installed per the manufacturer’s spec, and that’s where most failures start.
  • Arlington requires a permit for additions and ADUs. We pull them and get the inspection signed. Skipping that is the story that ends in a failed resale.
  • We’re not Owens Corning, and we’re not a parts counter. We buy the right part for your build and stand behind the installation with a written 90-Day Done Right Promise.

Which Owens Corning Models This Applies To

Owens Corning doesn’t sell “an addition.” They sell the components that make an addition’s shell hold together: FOAMULAR extruded polystyrene rigid board, Thermafiber mineral wool fire and sound batts, WeatherLock or Deck Defense underlayments, a long list of shingle series (Oakridge, Duration, Duration FLEX, Berkshire, TruDefinition), and loose-fill attic insulation. So the “model” you need to identify is really the part number on the specific piece that failed.

Start with the container or the board stamp. Insulation batts have an R-value and product number printed on the kraft face; foam board has a color, an R-value, and a product line stamped into the surface. Shingles are identified on the wrapper (Oakridge is 3-tab, Duration is architectural, Duration FLEX has its own spec) and, once installed, by the shingle thickness and tab profile. If the wrapper is gone, we measure. Foam thickness tells you R-value; shingle tab width and laminate layer tell you the series. If you can find the framing contract, the spec sheet usually lists the exact part number – that’s the fastest path.

OEM versus aftermarket isn’t a clean choice here. For a compatible foam board, a mineral wool batt, or an underlayment, a quality equivalent from another manufacturer will usually meet the spec and save money. For anything tied to a warranty or a code designation (fire-rated assemblies especially), use the exact Owens Corning part the assembly calls for. When we quote, we tell you plainly which one we’d use and why.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Owens Corning Home Additions & ADU Is Failing

  • Soft spots or a spongy floor along exterior walls. Usually a sign that foam sheathing or a flashing detail has let moisture behind the wall assembly. It starts small and spreads fast in a wet Texas spring.
  • Shingle edges lifting or curling on the addition roof. Duration and Oakridge shingles both lift at the rake when the starter course or the underlayment was installed too tight. On a low-slope addition roof, that turns into wind damage at the first 40 mph gust.
  • Water stains on a ceiling under the addition. Underlayment installed without the correct overlap or flashing, so the first hard rain finds the seam. Deck Defense and WeatherLock both need the specified lap; a shortcut there shows up months later.
  • A drafty or hot room above the addition. Loose-fill insulation that settled wrong, or foam board with gaps wider than the foam-safe sealant can bridge. Arlington’s summer heat finds every gap.
  • Visible mold or musty smell in the wall cavity. Insulation that got wet during construction and stayed wet. Batts that took on water lose their R-value and start to smell; that’s not a repair, that’s a tear-out.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Full home additions in Arlington run $45,000 to $130,000, and ADU construction lands between $90,000 and $220,000. What drives the range is size, foundation type, whether the addition touches the existing slab or a new one, the envelope spec you choose, and whether plumbing or electrical has to be relocated. A garage conversion to living space is a different number entirely, $30,000 to $80,000, and often the smartest path if you already have the shell.

Inside those numbers, parts cost is small and labor is the bulk of it. We don’t run a parts-plus-labor split as an add-on fee. Every material line and every labor allowance is itemized in the written quote before we start. If the scope changes mid-build (and sometimes it does, once a wall opens), the price change comes to you as a written change order before a single nail moves. No surprise invoices at the end. Every eligible job gets permits pulled and inspections signed, and the finished work is backed by our written 90-Day Done Right Promise.

DIY or Call Us?

You can safely do the detective work. Find the wrapper, photograph the stamp on the foam board, measure the shingle tab width, and check the framing contract for a part number. That work saves us a trip and saves you guesswork. Where DIY goes wrong is the installation itself: foam board tucked without the right foam-safe sealant, underlayment lapped backward, or shingles nailed into a new roofline with no starter course. Those mistakes don’t show up for a season, and by then the water damage is in the wall cavity, not the surface.

One more thing about an addition or ADU in Arlington: permitting. Every scope we touch gets a permit pulled and an inspection signed, because the inspector works for you, not for us. If the last contractor told you a permit was optional on a structure like this, that’s a problem we’d rather find now. Call (888) 590-9867 and we’ll talk through what’s actually failing and what it will take to fix it right.

FAQs

Need Construction help nationwide? Licensed & insured · free written estimates
Call (888) 590-9867
Local Service Coverage

Request a Free Estimate in Arlington

Tell us what you need - Barrett & Sons Construction Arlington responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Call Now - 24/7 Dispatch