Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Windows & Doors: The Arlington Owner’s Guide
We install and repair Boral windows and doors across Arlington, and most single-window or single-door replacements land between $450 and $1,500 installed, while a whole-house Boral window package typically runs $4,500 – $15,000. Impact-rated Boral units, which matter more every year in North Texas, run $8,000 – $25,000 for a full home. Parts and hardware swaps (operators, rollers, weatherstrip, glass) are cheaper and often same-day once we’ve identified the exact unit. Barrett & Sons Construction is an independent service provider and is not affiliated with Boral; we source genuine Boral parts and quality equivalents for the models we work on.
Owners usually find out something’s wrong in one of two ways. A door starts dragging on the sill in July. Or the glass fogs from the inside and no amount of Windex fixes it. Those two failures cost very different amounts to solve, which is why identifying the exact Boral product comes first. Every Boral window and door we touch gets measured, matched, and priced in writing before we cut anything.
Key Takeaways
- Fogged insulated glass is a failed seal, not a cleaning problem. The glass has to be replaced (or the sash, depending on the series).
- Dragging Boral doors in Arlington are often a roller or hinge problem, not a bad door. Hardware swaps are cheaper than replacements.
- We don’t stock parts on a truck or in a warehouse. We measure your unit and order the right part, genuine Boral or a matched equivalent, and we tell you which one we’re quoting and why.
- Every price change comes to you as a written change order before work starts.
Which Boral Models This Apply To
Boral makes windows and doors under a few different product families, and the parts don’t cross over cleanly between them. The two most common in Arlington homes are the aluminum and vinyl series on the residential side and the clad-wood and impact-rated lines common in newer construction. Boral’s impact products are specified in a lot of North Texas builds because of local wind-borne debris requirements, and those units use different glazing assemblies and different locking hardware than their standard counterparts. If your home was built or re-windowed after roughly 2015 in Arlington, there’s a decent chance you have an impact-rated unit and don’t know it. That matters the moment a roller or latch fails.
The fastest way to identify what you have: check the etched glass bug in the corner of one pane (it usually shows the manufacturer, the series code, and a date code), then check the frame or jamb for a label or the ENERGY STAR sticker. If those are gone, the interior sill or head jamb often has a stamped model number. Take a photo of the bug, a photo of the label, and a tape measure to the width, height, and depth of the rough opening. That’s everything we need to match a part.
On the OEM-versus-aftermarket question, here’s how we decide. For structural items (sash, glazing, frame components), we quote genuine Boral. For wear items (rollers, weatherstrip, sweep, operators, hinges, locksets), a quality aftermarket part is often identical in function, less expensive, and easier to source quickly. We tell you which path we’re recommending and why, and we don’t mark up the aftermarket option to make the OEM option look better. The customer should be able to look up exactly what’s going in their home.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Boral Windows & Doors Is Failing
Here are the five failures we see most in Arlington homes, and what’s actually causing each one – because the symptom and the fix are often not the same thing.
- Fogging or condensation between panes. The insulated glass unit’s perimeter seal has failed and moisture has entered the sealed cavity. This is not a cleaning issue and no product fixes it from the outside; the IGU (or the sash, on some series) must be replaced.
- The door drags or won’t latch flush. On sliding Boral doors, this is usually a worn roller, a bent track, or a hinge that’s lost its adjustment. On hinged doors, it’s often a sagging hinge plate or a strike that no longer lines up. Replacing the hardware is far cheaper than replacing the door.
- Drafts or water intrusion at the frame. Weatherstrip, sweep, and corner seals are the usual culprits. Texas heat and UV bake these materials faster than most homeowners expect, and the failure shows up as a draft in winter or a wet sill in a heavy Arlington rain.
- Sticking locks or operators that won’t turn. On casement and awning Boral units, the crank operator or the multi-point lock mechanism has worn or stripped. On sliding doors, it’s often the latch or keeper. These are replaceable without removing the unit in most cases.
- Water stains on the interior trim or drywall near the opening. This one is the one to take seriously. It usually points to failed flashing, a failed sealant joint, or a sill pan issue, and the fix is often more than the window itself. We look at the opening, not just the unit.
Replacement Cost & What’s Included
For Arlington, plan on these installed price ranges. The range reflects the size of the opening, the series you have, whether it’s impact-rated, and how much trim or drywall work is involved.
| Scope | Installed Price Range |
|---|---|
| Single Boral window or door replacement (standard) | $450 – $1,500 |
| Full Boral window replacement, whole home | $4,500 – $15,000 |
| Impact-rated Boral window installation | $8,000 – $25,000 |
| Hardware swap (rollers, operators, locks, weatherstrip) | Parts plus labor, quoted in writing |
What’s included: the part, the labor, and haul-away. Permits are pulled and inspections signed on every job where they apply, which for a straight like-for-like replacement is usually none – but we check, and we tell you, because the last contractor most folks used told them permits were optional. Every price change we recommend mid-job comes to you as a written change order before work moves. The work is backed by our 90-Day Done Right Promise: if something’s not right, one call brings us back.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Some things you can safely check on your own. Measure the rough opening, photograph the glass bug, test whether the fogging lifts with a hair dryer (it won’t, if the seal is gone), and confirm whether the door drags only in hot weather or all year. That last one tells us whether the roller is worn or the frame has shifted, and it saves a trip.
Where DIY goes wrong on windows and doors: prying a sash out of a frame to change the glass, drilling into a multi-point lock mechanism, or re-sealing a door frame without checking the flashing underneath. Those are the ones that turn a $250 hardware swap into a $2,000 repair. On the impact-rated Boral units, the glazing assembly is a sealed system and should not be opened or resealed by hand. If your door or window is the only one of its kind on the house and you’re not sure what you have, that’s the moment to call. Call (888) 590-9867 for a free estimate and we’ll tell you what you’re looking at before anyone touches it.
FAQs
Most Boral windows and doors last 20 to 30 years with normal care, but in North Texas the hardware and weatherstrip usually need to be replaced every 8 to 12 years because of heat and UV. The glass seal is the variable: a well-made IGU often goes 15 to 25 years, and a cheap or damaged one can fog in half that. If your unit is past 15 years and the seal or the roller has failed, replacing just that component is usually the right call. Call (888) 590-9867 for an exact quote – estimates are free.
Usually yes, especially on hardware and glazing. Fogged insulated glass, worn rollers, stripped operators, failed weatherstrip, and misaligned locks are all parts-level repairs, not replacement jobs. Whole-unit replacement only becomes the right answer when the frame itself is cracked, or when the water intrusion has gotten into the surrounding wall cavity. We look at the opening, not just the unit, before recommending any replacement. Call (888) 590-9867 for a free second opinion on any written estimate.
A single hardware or weatherstrip swap is typically a 1 to 2 hour visit. A glass or sash replacement runs 2 to 4 hours depending on the series. We don’t stock parts on a truck, so the timeline depends on sourcing. Lead time for a genuine Boral part is typically 1 to 2 weeks; a matched aftermarket equivalent is often 2 to 5 days. We tell you the sourcing path and the timeline before you approve anything. Call (888) 590-9867 to start the measurement.
We measure the unit and identify the series from the glass bug, frame label, or stamped jamb number, then quote genuine Boral or a quality aftermarket equivalent with the tradeoff written out. We don’t carry parts in a warehouse and we don’t guess. That’s the reason our quotes hold – an allowance that isn’t on paper is a surprise waiting for a date. Call (888) 590-9867 for a free estimate.
Where We Work Boral Windows & Doors in Arlington
We work Boral windows and doors all over Arlington – from the older brick ranch homes near downtown to the newer subdivisions along I-20, where impact-rated units are more common. If your home has KraftMaid or Cambria in the kitchen and you’re re-doing the windows in the same breath, we can quote those at the same time; Silestone and Cambria counters, KraftMaid cabinetry, and Boral windows are the brands we handle most often on a whole-house refresh. Different rooms, same crew, one set of written change orders. Our crew members have up to 28 years of experience, they’re background-checked, and every price change arrives as a written change order before work starts. Call (888) 590-9867 to schedule your free estimate – a live person answers, not a voicemail box.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.