A Barrett company - serving Arlington, TX

CGI Windows & Doors in Arlington, TX

Windows & doorsWindows & doors
Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

CGI Windows & Doors in Arlington, TX

CGI Windows & Doors: The Arlington Owner’s Guide

CGI (a well-known Texas manufacturer of windows and doors) is a name a lot of Arlington homeowners already know, especially in homes built or updated in the 1990s and 2000s. So we get a steady stream of calls like this: “The glass is fogged, the sash won’t close tight, the door is dragging” and “What part do I need, and what’s it going to cost?” Here’s the honest answer: we install CGI-compatible replacement windows and doors in Arlington, and most whole-home window swaps run roughly $4,500 to $15,000 installed (single doors and specific replacements priced by part). We’re an independent local contractor, not CGI itself – we don’t manufacture CGI products, but we work with matching and equivalent components every week.

Call (888) 590-9867

Owners usually find out a window or door is failing the same few ways. A bedroom glass goes cloudy at the edges and you can’t see out. A sliding patio door starts to stick, then won’t latch. The AC runs nonstop in July and you feel hot air pouring off the west-facing glass. Or a neighbor mentions their CGI windows hit the same age and they swapped them out. That’s how it goes – here in Arlington you find out all at once, when the symptom finally gets your attention.

Which CGI Models This Applies To

If your home has CGI windows or doors, the first step is identifying which line you actually have, because that determines which replacement part or whole unit fits. CGI made several product families over the years, and parts don’t always cross over between them. Find the label – usually on the window sill or inside the sash channel, or on the door edge – and note the model and series. If the label is gone, we identify the unit by frame profile, glazing type, size, and installation style.

The OEM-versus-aftermarket call matters more than the sales pitch suggests. A factory-correct part guarantees the fit and finish, but for some older CGI lines the OEM part is discontinued or prohibitively priced. A quality aftermarket equivalent can do the job – if it’s matched to the exact frame and operating style, not a “looks close” substitute. That’s where a real measurement beats a phone conversation. Speaking of brands, we also work with KraftMaid, Cambria, and Silestone on the interior finish side of these jobs.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your CGI Windows & Doors Is Failing

Here’s what we hear most in Arlington, and what each symptom usually points to underneath:

  • Foggy or cloudy glass. That outer seal has failed and moist air has gotten between the panes, so the glass itself is the culprit, not the frame.
  • Drafts or hot air at the edges. Weatherstrip and glazing seals have flattened or split, and the sealing gasket that quietly kept North Texas heat out isn’t sealing anymore.
  • Sticking or dragging sashes and doors. The frame or hardware has shifted, often from the seasonal clay-soil movement common across Arlington; the gliding hardware or rollers may also be worn.
  • Water intrusion or rot at the sill. A failed seal or a clogged weep hole lets water sit where it shouldn’t; on older units this shows up as soft wood or peeling paint at the bottom corner.
  • Hard-to-turn handles or locks that don’t catch. The hardware has worn or the door has shifted out of square, so the lock is fighting the frame instead of meeting it.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Here’s the ballpark for Arlington, and we’ll always come measure and quote your actual job. For reference, the typical whole-home window replacement is $4,500 – $15,000, and impact-rated window installation (a smart pick given Texas hail season) lands at $8,000 – $25,000. A single door or window already runs a smaller figure, priced by size, glass type, and how much framing has to be repaired.

What drives the range: number of windows, size and glazing choice, whether we’re replacing the unit or repairing a part, and how much rot or frame repair the opening needs. Our quotes are line-item and written, and no scope change happens without a written change order first – so the number you sign is the number you pay. Finished work carries our 90-Day Done Right Promise.

DIY or Call Us?

Some things you can safely check yourself. Read the label for your model. Wipe the sill and clear the weep holes. Note where the draft or water is coming from and whether the sash or door is out of square. If the fogged glass is a whole sealed unit (double-pane), that’s a factory-sealed part – don’t try to crack it open or reseal it yourself; the risk of broken glass and a worse leak is real. If a door’s frame has shifted, or the hardware is fighting you, that’s where it gets out of hand. Give us a call at (888) 590-9867 and we’ll tell you straight whether it’s a part or a whole unit.

FAQs

How long do CGI windows and doors last? A well-built CGI window typically gives you 15 – 20 years, though the hard Texas sun and hail accelerate things – in Arlington, glass seals often fail before the frame does, so fogging is your early warning.

Can it be repaired instead of replaced? Yes, often. A worn roller, weatherstrip, or hardware set is usually repairable at a fraction of replacement cost; fogged sealed glass and rotted frames usually aren’t worth repairing. We’ll tell you which you’re dealing with.

How long does the swap take? A single window or door is usually a half-day to a full day; a whole-home replacement runs several days. We give you a real schedule, not a phone number that turns into a runaround.

How do we source the part? We match the part to your exact CGI model and series – OEM-correct where it’s available, a quality equivalent where it isn’t. No mystery brands off a van.

Call (888) 590-9867 to schedule your free estimate. A live person answers, the quote is written, and the work carries the 90-Day Done Right Promise.

Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.

Need Construction help nationwide? Licensed & insured · free written estimates
Call (888) 590-9867
Local Service Coverage

Request a Free Estimate in Arlington

Tell us what you need - Barrett & Sons Construction Arlington responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Call Now - 24/7 Dispatch