Roofing
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CWS Roofing: The Arlington Owner’s Guide
Barrett & Sons Construction Arlington installs and repairs CWS-compatible roofing systems, and most roof work in Arlington runs $400 – $1,800 for a repair or $8,000 – $20,000 for a full replacement. Scheduling is planned rather than same-day; a repair estimate usually happens within a few days of your call. Most Arlington owners discover the failure the same way: a brown water stain creeping across a ceiling after a spring storm, granules collecting in the gutter downspouts, or a shingle tab curling up on the south slope where the Texas sun hits hardest. By the time you see any of those, the underlayment has usually been wet for a while.
We’re an independent contractor and we’re not affiliated with CWS. We install and repair their systems, and we tell you honestly whether a part-level fix gets you through the season or whether the deck itself has reached the end.
Which CWS Models This Applies To
CWS (sometimes sold under the CertainTeed and GAF umbrellas depending on the shingle line and the year it was milled) has run several profile families through North Texas: three-tab strips on older homes, architectural laminated shingles on the bulk of Arlington subdivisions built from the late 1990s on, and the heavier designer profiles on the larger custom builds. Each family has its own exposure spec, usually 5″ on a three-tab and 5-5/8″ to 8″ on an architectural shingle, and that exposure number is the compatibility gotcha most homeowners miss. Order an architectural replacement for a three-tab roof and the nail line won’t land where the old one did, so the shingle won’t seal flat and the laps won’t match.
Here’s how to identify what’s on your roof. Check the underside of a shingle tab at the eave, or the shaded slope over the garage, for a printed or stamped manufacturer mark. Measure the exposure (the visible part of each course) with a tape from the bottom edge of one course to the bottom edge of the next. Count the tabs across a 36-inch width if it’s a strip shingle. Match that measurement to the CWS spec sheet rather than guessing from a photo.
The OEM-versus-aftermarket decision matters here. A true OEM match keeps the color and profile consistent with what’s already on the roof. A quality aftermarket equivalent from GAF or CertainTeed can be the smarter call when the original line is discontinued, which happens often on Arlington roofs past the fifteen-year mark. What we won’t do is slap a mismatched shingle on a visible slope and call it a match. If the color lot is off, we say so before the first bundle comes off the pallet.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CWS Roofing Is Failing
Roof problems in Arlington show up in a predictable order because of our climate: brutal summer UV, hail in spring, and the freeze-thaw swing that cracks sealant and opens nail holes. Here’s what to watch for.
- Granules in the gutters and at the downspout splash blocks. The mineral surface is shedding, which means the asphalt underneath is thinning and the shingle is losing its UV shield. Once granules are gone, the shingle ages fast.
- Curling or clawing tabs on the south and west slopes. Those two faces take the most afternoon sun in Arlington, and the thermal cycling lifts the sealant strip. A lifted tab is a wind-catching tab, and hail finds it next.
- Dark water stains on ceilings or at the wall-to-ceiling joint. The shingle isn’t the only suspect; the flashing around a chimney, vent boot, or skylight is often the actual leak. A stain means water has been traveling for a while.
- Lifted or cracked flashing at penetrations. Sealant around vent pipes and chimney counter-flashing dries out and splits after a few Texas summers. This is the most common leak source we find on otherwise sound roofs.
- Sagging or soft spots in the deck between rafters. This is the serious one. It usually means long-term moisture has reached the sheathing, and it points to a repair that goes beyond shingles.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Arlington, a CWS roof repair runs $400 – $1,800, and a full roof replacement runs $8,000 – $20,000. Metal roof installation runs $15,000 – $40,000, and tile roof repair runs $600 – $2,500 if your home has a tile section. Those ranges hold because the price depends on roof size, pitch, how many layers need tearing off, how much decking needs replacing, and whether the flashing set has to be rebuilt from scratch.
You get a written line-item quote before anything starts: tear-off, underlayment, shingles or replacement part, flashing, and disposal each priced on their own. If we open the roof and find rotten decking that wasn’t visible from the ground, that change arrives as a written change order before we touch it, not as a surprise line on the final invoice. Every eligible job gets the permit pulled and the inspection signed. Our technicians have up to 28 years of experience, and the work is backed by our 90-Day Done Right Promise: if it’s not right, we come back and make it right.
DIY or Call Us?
Some roof checks are safe to do from the ground. Grab binoculars and look at the slopes for curled tabs, missing shingles, and rusted or lifted flashing. Check your attic on a dry day for daylight through the deck and water staining on the rafters. Clear the gutters so you can see what’s collecting in them.
What you shouldn’t do is climb up and start prying shingles or re-sealing flashing yourself. Roofing is height work, and a fall from a two-story Arlington roof is a serious injury. Beyond the fall risk, a shingle pried up and re-nailed in the wrong spot, or sealant smeared over a flashing that was actually the leak, hides the real problem and lets water keep traveling. A roofer with the right ladder setup and fall protection can find the leak source in an afternoon and fix the right thing the first time. Call us at (888) 590-9867 if you want a second set of eyes on it.
FAQs
How long does CWS roofing last in Arlington weather? A CWS architectural shingle typically lasts 15 to 22 years in Arlington, shorter than the manufacturer’s headline rating because our summers and hail seasons age the sealant faster than a mild climate would. Shade, roof pitch, and attic ventilation all move that number up or down. Call (888) 590-9867 and we’ll give you an honest read on the roof you have.
Can it be repaired instead of replaced? Often yes. A single failed shingle, a cracked vent boot, or lifted flashing can be repaired for $400 – $1,800 without touching the whole roof. If the deck is soft or more than a quarter of the roof is failing, repair stops being the value play and we’ll tell you so plainly. Call (888) 590-9867 for a free estimate and a straight answer.
How long does the work take? A repair is usually done in a few hours, and a full roof replacement on a typical Arlington home runs one to three days depending on size, pitch, and weather. We work around Texas afternoon storms rather than tearing off more than we can dry in. Call (888) 590-9867 to schedule your free estimate.
How do you source the part? We match your roof to the CWS spec and order the correct shingle profile, flashing, and underlayment from our suppliers; we don’t carry parts on a truck and we don’t guess from a photo. We’re not affiliated with CWS, so we order what your roof actually needs, not what a single brand line happens to push. We also install KraftMaid, Cambria, and Silestone on the interior side.
Call (888) 590-9867 for a free estimate on your CWS roof repair or replacement in Arlington. We’ll look at it, put the scope in writing, and tell you the truth about whether it’s a patch or a full roof.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.