Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CWS Fence Installation: The Arlington Owner’s Guide
Fence installation with CWS products here in Arlington runs most homeowners between $3,500 and $9,000 for a full yard, depending on footage, material and site conditions. We install CWS-compatible fencing with materials matched to your panel and post system, and we schedule around your project rather than promising a same-day swap. Most owners discover the problem months after the fact: a gate that drags the ground, a post that’s leaned a few degrees off plumb, a cedar or vinyl panel that started bowing after a summer of 100-degree days followed by a spring storm blowing through Tarrant County. CWS makes several fence lines, and installing the wrong post spacing or rail gauge for your series is the most common reason a fence underperforms in North Texas weather.
Which CWS Models This Applies To
CWS carries wood, vinyl and composite fence systems, and each family uses different post dimensions, rail profiles and fastener types. A vinyl privacy line might call for 5×5 posts set 96 inches on center, while a wood picket system may run 4×4 posts at 8-foot spacing with specific steel fastener heads. Before we order a single panel, we measure your existing post spacing and rail height, then check the panel label or the gate hardware stamped with the CWS series code. That label normally sits on the inside face of the gate frame or the top rail cap; if it’s weathered off, we measure the rail profile and post thickness to match the line.
Aftermarket fence parts exist for common CWS lines, and for rails, caps and pickets the quality copies hold up fine. For posts and gates, we lean toward OEM or OEM-spec materials because the post wall thickness and the gate hinge weld are where fakes fail fastest. We won’t tell you an aftermarket panel is an OEM panel; we’ll tell you which grade it is and what lifespan to expect. Barrett & Sons Construction Arlington is an independent installer and not affiliated with CWS.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CWS Fence Installation Is Failing
- Leaning posts. The post hole was undersized or the concrete wasn’t set below the frost-and-expansion line for Arlington’s black clay soil. Clay swells and shrinks hard through a wet spring and dry summer, and a shallow footing walks out within a few seasons.
- Bowing or sagging panels. The top rail gauge is too light for the width, or the picket fasteners loosened after UV exposure. Composite and vinyl panels are the usual suspects once they’ve baked through a Texas August.
- Gate drag and hinge wear. Gate hinges and the post jamb take the most load on any fence run, and a hinge that’s 1/8-inch out of alignment starts dragging the gate within a month. That drag strains the post and the latch.
- Rot at the post base or rail ends. Wood pickets and rails wick moisture at the end grain where they meet the post. If the end grain wasn’t sealed at install, you’ll see softening within three to five years in North Texas humidity.
- Loose or popped fasteners. Wind moves a fence more than people expect. Fasteners backed out of a rail mean the fastener either wasn’t the right type for the material or was overdriven at install.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Full CWS-compatible fence installation in Arlington typically lands in the $3,500 to $9,000 range, and the number moves with linear footage, material family, gate count and how much old fence or bad footing has to come out. A straightforward vinyl privacy run at 150 feet with one gate sits near the low end; a wood privacy run with a double gate, corner posts and a corner lot’s worth of tear-out pushes toward the top. We write every scope, every material callout and every allowance on the estimate, and any price change arrives as a written change order before we pick up a tool. Materials, labor, post setting, gate hardware, cleanup and haul-off are all listed line by line. The finished job is backed by the written 90-Day Done Right Promise, and our technicians have up to 28 years of experience on installs like this.
DIY or Call Us?
You can safely check the easy things on your own: walk the fence line and look for lean, push on a corner post to feel for looseness, and check whether the gate swings on its own. What goes wrong on a DIY fence install isn’t the panel work; it’s the footings. CWS systems care about post hole depth, concrete diameter and plumb, and in Arlington’s clay, a post set too shallow will start leaning the first time the ground swells. If you’re replacing a single picket or tightening a hinge, that’s reasonable work. If you’re resetting posts or replacing a run of panels, that’s where a crew with the right auger, the right concrete mix and a level saves you a second job in two years. Call (888) 590-9867 and we’ll walk you through what your CWS series needs.
FAQs
A properly installed CWS vinyl or composite fence in Arlington should hold 15 to 20 years, and a wood fence 10 to 15 with end-grain sealing every few years. Lifespan comes down to footings and post material more than the panel itself; a fence set shallow in North Texas clay loses years fast. Call (888) 590-9867 for an exact quote on your run – estimates are free.
Often yes. A leaning post, a dragging gate or a few bowed panels can be repaired without tearing out the whole line, and if the posts are sound, a repair runs a fraction of a new install. We’ll tell you honestly when a repair is the right call and when the footing or rail is too far gone. Call (888) 590-9867 and we’ll come look.
A typical residential run in Arlington takes one to three working days once materials are on site, and tear-out plus footing cure adds to that on a full replacement. The most useful number we can give you up front is the written schedule on your estimate, which we hold to. Call (888) 590-9867 to set up a free estimate.
We order the panel, post and rail materials matched to your CWS series and measure your existing post spacing and rail profile before ordering anything. We don’t carry parts on a truck or keep a local stock; each job’s materials are sourced for that installation so the match is right. Call (888) 590-9867 and we’ll talk through what your fence needs.
If your CWS fence line has a post leaning, a gate dragging or a panel that’s given up, we’d rather look at it than guess over the phone. Every project starts with a free written estimate, itemized top to bottom, with no trip charge inside the county and a free second opinion on any written estimate you already have. Proudly serving Arlington and the surrounding communities from our owner-operated shop – Tom Barrett’s name, address and license number are published, and you’re welcome to look them up before you sign anything. We’re also happy to talk through premium-brand work in other trades, including KraftMaid, Cambria and Silestone, if your project grows.
Call (888) 590-9867 for a free estimate on your CWS fence installation in Arlington.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.