A Barrett company - serving Arlington, TX

Barrette Kitchen Remodeling in Arlington, TX

Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Barrette Kitchen Remodeling: The Arlington Owner’s Guide

In Arlington, kitchen remodeling projects with Barrette cabinetry and millwork typically run $14,000 to $45,000 installed, and a cabinet, door, or millwork component failure is usually addressed within a scheduled visit, not a same-day trip. If a Barrette door is sticking, a drawer box has cracked, or a hinge plate has pulled from the cabinet frame, the practical path is a measured replacement matched to your exact Barrette line and finish, not a universal part. Call (888) 590-9867 for a free estimate on the correct scope.

Call (888) 590-9867

Most Arlington homeowners find us after noticing a soft, sagging drawer bottom or a door that won’t stay shut once the humidity climbs. Those symptoms look minor until you open the cabinet and see the damage underneath: cracked plywood, stripped screw holes, a hinge pulling out of the frame. That’s the point where the part matters more than the polish.

Quick takeaways:

  • Installed kitchen range in Arlington: $14,000 – $45,000.
  • Cabinet installation alone: $4,000 – $13,000.
  • Countertop replacement: $2,000 – $6,500.
  • Backsplash: $800 – $2,500.
  • Barrett & Sons is an independent contractor and not affiliated with Barrette.

Which Barrette Models This Applies To

Barrette cabinetry and millwork spans framed and frameless lines, and the part that fits one series will not fit another. The label inside the cabinet door or on the back of the drawer box is your starting point – that sticker carries the series, the finish code, and sometimes the width. Write it down before you call anyone. A photo of the label plus a tape measure across the door front and the drawer opening tells us more than a description ever will.

Two compatibility points trip up Arlington owners:

  • Hinge pattern changes within a line. Barrette has revised hinge cup bore spacing over the years, and a replacement door cut for the older pattern will not align with newer frame drilling. Measure the bore spacing, don’t assume.
  • Finish codes drift. The same “white” or “maple” name can cover two different production runs. A door pulled from a current catalog may read a shade off against cabinets installed a decade ago.

On the OEM-versus-aftermarket question: a factory Barrette replacement door or drawer box is the only way to guarantee an exact finish match. Quality aftermarket hardware (hinges, slides, shelf pins) is a reasonable substitute when the original hardware has been discontinued – brands like Blum and Grass make hardware that fits Barrette drilling patterns, and we’ll tell you plainly which way makes sense for your cabinet. We don’t claim to stock Barrette parts or carry them on a truck. We source them for your job.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Barrette Kitchen Remodeling Is Failing

Arlington’s summer heat and humidity work on wood cabinets the way they work on everything else here. The failures we see most often:

  • A drawer bottom sagging or bowing. Usually a thin lauan or particleboard bottom that has absorbed moisture. In older cabinets the bottom was stapled, not dadoed, and once it swells it never lays flat again.
  • Hinges pulling out of the frame or door. The screw holes strip when the door gets slammed or the cabinet swells. A hinge plate that’s migrated more than a sixteenth of an inch is telling you the wood around it is compromised.
  • A door that rubs or won’t close flush. Often a hinge adjustment problem, but sometimes a warped door from a finish failure. Check whether the gap along the top is even before you touch the screws.
  • Delamination or peeling veneer at the edges. Moisture gets behind the veneer at the door edge or under the sink and lifts it. Left alone, the substrate swells and the door is done.
  • Cracked or split drawer boxes. Common in frameless cabinets where the box carries the load. A split at the corner joint means the box needs replacing, not regluing.

One pattern worth knowing: cabinets set against an exterior wall in an Arlington kitchen take more seasonal movement than cabinets on an interior wall, because the wall itself expands and contracts with the heat. If the failures cluster on one side of the kitchen, that’s the reason.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

Here’s the honest price picture for Arlington. These are installed ranges, not parts-only prices, because the labor is where the surprises live.

Scope Installed range
Full kitchen remodel (Barrette cabinetry) $14,000 – $45,000
Small kitchen remodel $9,000 – $20,000
Cabinet installation or replacement $4,000 – $13,000
Countertop installation $2,000 – $6,500
Backsplash installation $800 – $2,500
Kitchen island installation $3,000 – $10,000

What moves a job toward the top of the range: custom door sizes, a finish that requires a full run to match, countertop removal and reinstall, or plumbing and electrical changes behind the cabinets. Single-door or single-drawer replacements sit well under the cabinet range, and we quote them as a line item, not a package.

Every scope, allowance, and price change arrives in writing on a change order before work starts. No surprise invoices. Every eligible job is permitted and inspected, and the finished work is backed by our written 90-Day Done Right Promise.

DIY or Call Us?

Some of this an owner can check safely. Adjusting a European hinge with a screwdriver is fine. Tightening a loose cabinet pull is fine. Measuring a door and photographing the label is exactly what we’d ask you to do anyway.

Where it goes wrong: regluing a drawer box that has already delaminated, or forcing a replacement door onto a hinge pattern that doesn’t match, which cracks the frame and turns a $90 part into a $900 cabinet repair. If a cabinet is mounted over a gas line, a dishwasher connection, or an electrical junction box, don’t drill or pry near it – that’s a call to a licensed trade, and we’ll tell you so. Our crews have up to 28 years of experience and we’re insured and bonded. Call (888) 590-9867 for a free second opinion on any written estimate.

FAQs

Need Construction help nationwide? Licensed & insured · free written estimates
Call (888) 590-9867
Local Service Coverage

Request a Free Estimate in Arlington

Tell us what you need - Barrett & Sons Construction Arlington responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Call Now - 24/7 Dispatch