Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Belgard Driveway & Pavers: The Arlington Owner’s Guide
We install Belgard pavers for Arlington driveways, and a paver driveway here typically runs $7,000 to $18,000 installed, depending on square footage, base prep and whether an old slab has to come out first. Most Arlington homeowners find out something is wrong when a paver rocks underfoot after a rain, when sand starts washing to the curb, or when a hairline crack opens along a joint and keeps coming back no matter how many times it gets filled.
Belgard makes the pavers, not the base under them. That distinction matters because in our experience, nine out of ten “Belgard problems” in Arlington are installation problems: shallow base, a driveway poured too close to the slab, drainage running back toward the house. We’re an independent contractor and not affiliated with Belgard, so we can tell you plainly which problem is the product and which is the ground beneath it.
Key Takeaways
- Belgard paver driveways in Arlington run $7,000 to $18,000 installed.
- Most failures are base and drainage problems, not failed pavers.
- Individual pavers can be lifted and reset without tearing out the whole driveway.
- We pull permits and sign inspections on eligible work, and every job carries our 90-Day Done Right Promise.
Which Belgard Models This Applies To
Belgard sells paver driveways through a handful of product families, and knowing which one you have tells us how to reset or match it. The three Arlington homeowners most often have are Aqualine (permeable, open-joint), Urbana Stone and Mega-Lafitt (the larger-format structural pavers used on driveways), and the older Dublin Cobble and Cambridge Cobble lines that show up on homes built here in the 1990s and 2000s.
The fastest way to identify yours is the joint pattern. Aqualine and other permeable systems sit on wider joints filled with open-graded aggregate, while a standard structural paver on a sand-bed joint sets tight with polymeric sand. If the original installer left a spare bundle in the garage or shed, the wrapper tells you the series, the color and the factory SKU. Without that, we measure length, width and thickness with a caliper and match against manufacturer specs. A full-size Mega-Lafitt is roughly 2 3/8 inches thick, the standard the base has to be built to carry. That thickness and the base depth are what the next owner inherits, so getting the model right matters for resetting a single paver and for a full replacement later.
OEM Belgard pavers are the answer for anything visible. Color lots shift from one production run to the next, and a generic big-box paver will not match a three-year-old Belgard field, even in the same color name. We source genuineBelgard product for visible repairs and note honestly that color-batch matching is never exact. Where the part is invisible (base aggregate, geotextile fabric, polymeric sand), a quality equivalent is fine.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Belgard Driveway & Pavers Is Failing
- Pavers rocking underfoot after a rain. The bedding sand under that paver has washed out or the base was never compacted to depth. This is the warning sign, and a paver that rocks in spring moves toward failure by summer.
- Sand washing to the curb or street. Either the joint sand was not topped off during the last rain, or water is running across the driveway because the slope wasn’t built to shed it. Both are drainage problems, not paver problems.
- A joint that keeps cracking open after filling. Polymeric sand that fails this way was usually installed too wet, or over a joint that was never tight. Re-filling it without addressing the joint will produce the same crack in the same place.
- Settling or a low spot where water pools. Base depth in Arlington’s clay soil is where this starts. Clay holds water, and a shallow base will move. The spot doesn’t fix itself.
- Chips and broken corners along the driveway edge. Usually the edge restraint has failed and the pavers are spreading. The pavers themselves are fine; the edge is what needs attention.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Arlington, a paver driveway installed runs $7,000 to $18,000 with Belgard product and a properly built base. The range is driven by square footage, base depth, whether an old concrete slab is removed, and edge restraint. A single-paver reset is priced as a small repair, well under the full-install number. If the base is sound and only the surface needs work, sealing runs $250 to $700 and is the cheapest way to add years to a Belgard field.
Every quoted price is a written, line-item estimate: parts, base prep, sand, edge restraint, labor. If the job uncovers a base problem nobody could see, you get a written change order before we lift a paver. We pull permits and inspections where the work requires it, and every completed job is backed by our 90-Day Done Right Promise. If it’s not right, you call us and we come back.
DIY or Call Us?
There’s real value in what a homeowner can do safely: sweep back the joint sand and check for voids, note which pavers rock, check that downspouts aren’t dumping onto the driveway, and lift a single loose paver to see what’s underneath. Anyone can look. What goes wrong is the reset. A paver lifted and set back on uncompacted sand will rock again within a season, and the real fix (base, compaction, edge) is heavy work. On a driveway, a paver edge restraint failure that goes unaddressed spreads the field, and by the time it’s visible it’s a bigger job than it was.
If the paver is cracked, rocking or the joint has failed, call us at (888) 590-9867. We’ll look at it, tell you honestly whether it needs a reset or a new base, and give you a free estimate. No trip charge inside the county, and the free second-opinion offer stands on any written estimate you’ve already received.
FAQs
A Belgard paver itself will last 30 years or more, but the driveway only lasts as long as the base under it. Here in Arlington’s clay, a properly built base is the line between 30 years and 10. The paver is the durable part; the installation is what determines lifespan.
Yes, in most cases. A single cracked or rocking paver can be lifted and reset, and a spreading edge can be re-restrained without touching the whole field. Replacement is the answer when the base under a large area has failed, not when one paver has.
A single-paver reset is a short visit, usually an hour or two on site. A partial-area reset where the base has to be rebuilt is quoted in days, and a full driveway replacement in weeks, depending on square footage and whether an old slab is removed.
We match your existing product by series, color and factory SKU, or by measuring thickness and dimensions against manufacturer specs when no spare bundle exists. We order genuine Belgard for visible repairs, add the new material into the field and note honestly that color-batch matching is never exact.
We also handle KraftMaid, Cambria and Silestone cabinetry and stone if your project touches more than pavers.
Call Barrett & Sons Construction Arlington at (888) 590-9867 for a free estimate on your Belgard paver driveway. We serve homeowners across Arlington and the surrounding area, and a live person answers the phone, every time.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.