Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Atlas Driveway & Pavers: The Arlington Owner’s Guide
We install Atlas paver and hardscape systems across Arlington, and the homeowner’s share of a paver driveway runs $7,000 to $18,000 installed, with most Arlington jobs landing between $9,000 and $14,000 depending on square footage and base prep. Concrete alternatives run $4,500 to $12,000, and asphalt sits lower at $3,500 to $9,000. When a paver system starts to fail, you usually notice it one of two ways: a rut or dip that catches your tire pulling into the drive, or a section of pavers that heaves and rocks after a hard freeze. Either one points to the same two culprits – base failure underneath or joint sand that washed out.
We’re an independent contractor, not affiliated with Atlas. What we know is how their systems go together and what fails first in North Texas soil.
Which Atlas Models This Applies To
Atlas covers a deep catalog, and matching the right profile matters more than most people expect. Their Euclid and Nantucket lines are the two you’ll see most often on Arlington driveways – Euclid is a tumbled, older-style brick look, Nantucket runs more uniform. Both measured in standard 4×8 and 4×9 nominal face dimensions, but the actual dimensions vary by production run, so we measure what’s on your drive rather than trust the label. If you’re patching a section, pull three pavers from a hidden corner and take them to a supplier for a physical match.
The compatibility gotcha: Atlas color lots shift between production runs. A “Sierra Blend” paver from a 2021 run will read noticeably warmer than the same color from 2024. If you’re blending new into existing, order the full face quantity for the repair from one lot and expect a slight tone difference at the seam. OEM matching is nearly impossible on discontinued profiles – quality aftermarket equivalents from Belgard and Techo-Bloc are what we typically source, and they hold up just as well. KraftMaid, Cambria and Silestone aren’t related to this work, but we carry them on interior jobs if you’re remodeling a kitchen while we’re already on site.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Atlas Driveway & Pavers Is Failing
- Rutting or tire-track depressions. Base compaction failed under the wheel path, usually because the original installer poured too thin. In Arlington’s black clay soil, a 4-inch base reads fine on paper but gives way inside three summers.
- Pavers rocking when you step on them. The bedding sand has washed out or shifted. Left alone, the paver edge chips and the failure spreads across the drive.
- Sand joint erosion and weed growth. Polymer sand breaks down faster when Arlington’s spring rains run off a poorly sloped drive. We see this most on north-facing drives that stay damp longer.
- Heaving or lipping after a hard freeze. North Texas doesn’t freeze often, but when it does, saturated base material expands and pushes pavers up. Lipping of a quarter inch or more is a sign the base drainage is wrong.
- Efflorescence – white chalky staining. Not a structural failure, but it tells you water is moving through the pavers and base. If it keeps returning after cleaning, the moisture source is underneath, not on top.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what honestly drives the number in Arlington:
| Scope | Installed Range |
|---|---|
| Paver driveway installation (full) | $7,000 – $18,000 |
| Concrete driveway alternative | $4,500 – $12,000 |
| Asphalt paving alternative | $3,500 – $9,000 |
| Full driveway replacement | $5,000 – $14,000 |
| Sealing (existing drive) | $250 – $700 |
| Paver patio installation | $3,500 – $11,000 |
The range in paver work comes down to square footage, base depth (we run 4 to 6 inches on Arlington clay), edge restraint, and whether we’re tearing out an existing slab. Every scope, allowance and quantity lands on paper before we start. Any change gets a written change order. The finished work is backed by our 90-Day Done Right Promise.
DIY or Call Us?
Pavers are one of the few exterior trades where partial DIY actually works. You can pull up a rocking paver, reset the bedding sand, and re-set it with a rubber mallet and a level – that’s a Saturday afternoon. You can re-sand joints and re-apply sealer. You can power-wash efflorescence.
Where owners get in trouble: tearing into a settled drive to fix the base. Once you pull the pavers up, the failure underneath is almost always deeper than the visible dip, and setting pavers back on a compacted repair patch without proper plate compaction and open-graded base is what creates the next dip in eighteen months. If your drive has more than a dozen rocking pavers or any dip deeper than a half inch, that’s base work, and it’s not a handyman job. Call (888) 590-9867 and we’ll walk your drive with you and tell you straight whether it’s a repair or a rebuild.
FAQs
A properly installed paver driveway in Arlington runs 25 to 30 years with joint sand kept up and sealer re-applied every three to five years. The pavers themselves will outlast the base if the base wasn’t compacted right. On the black clay soil across Arlington, we see base failures starting at year six to eight when the original install was under-prepped. Call (888) 590-9867 for a free evaluation – estimates are free.
Yes, if the failure is limited to a section or a joint issue, a targeted repair is often the right call and runs far less than a full rebuild. Discrete repairs we do regularly in Arlington: resetting a rocking section, replacing a settled area two to four times the visible failure, and re-sanding joints across the whole drive. If the base is failing across more than thirty percent of the drive, a partial patch will keep costing you money. Call us for a walk-through before you commit to either path.
A full paver driveway install for a typical single-car-wide Arlington driveway takes about four to six working days – one day of tear-out and haul-off, two days of base prep and compaction, one to two days setting pavers and cutting edges, and the last day for joint sand and cleanup. A section repair is usually a single day. Weather adds a day here and there, especially in spring.
We source through regional Atlas distributors and, where the original profile is discontinued, through quality equivalents from Belgard and Techo-Bloc, matched by face dimension and finish. We don’t stock product and don’t carry any on a truck – we order the exact quantity for your job from one lot so the color matches. You get the spec sheet and the lot number before we place the order.
If your drive is rocking, settling, or missing joint sand, that’s a call worth making. Call Barrett & Sons Construction Arlington at (888) 590-9867 to schedule your free estimate. We pull permits where they apply, we put every scope and every price change in writing before work starts, and the crew that shows up is the crew whose name is on the truck. Ask anyone on your street – or look up the license number yourself. A live person answers that phone, around the clock.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.