Home additions & ADU
Kitchen remodeling
Bathroom remodeling
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Atlas Home Additions & ADU: The Arlington Owner’s Guide
Barrett & Sons Construction Arlington installs Atlas-compatible home additions and ADUs, with typical projects in Arlington landing between $45,000 and $130,000 for an addition and $90,000 to $220,000 for a full ADU. If you’re here because a part failed, you’re probably not pricing a whole build – you’re chasing a specific component that’s letting water in, sagging, or not sealing. Most often it’s a door or window the addition has outgrown, a foundation shim that has crushed under North Texas clay, or a flashing detail on the roof tie-in that started leaking after a spring hailstorm.
Which Atlas Models This Applies To
Atlas builds several lines of addition and ADU components, and the part that fits one series won’t fit another. The version identification you need lives in three places: the data plate on the addition’s exterior door (usually a riveted metal tag near the hinge), the sticker inside the access panel on the new wall, and any paperwork the previous owner left in the house file. The series code on that plate tells you which door, window, and flashing profile came with your unit. If the plate is gone, a measuring tape gets you close – frame width, threshold height, and rough opening all need to match within 1/4 inch, and an “almost fits” part is the most common reason a home addition project in Arlington comes back for a second visit.
On the OEM-versus-aftermarket call: Atlas-branded replacement parts are the safe pick for anything that carries load or seals water, because the tolerances on an addition frame are tighter than they look. Quality aftermarket equivalents – like the door and window brands we install alongside Atlas (Andersen and Marvin) – are a reasonable option for non-structural trim and hardware. We’re an independent contractor and not affiliated with Atlas; we match to the part, not to a badge. If you’re also replacing kitchen or bath surfaces during the project, we carry KraftMaid, Cambria, and Silestone as well.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Atlas Home Additions & ADU Is Failing
- Water staining on the interior wall seam where the addition meets the original house. The flashing at the tie-in has separated or the sealant has aged out. Arlington’s summer storms drive water sideways, and that seam is the first place it finds.
- A new wall that’s out of plumb by more than a quarter inch over eight feet. Usually a foundation shim has crushed under the expansive clay soil common to Arlington, and the pier is no longer carrying its share.
- Exterior door sticking or dragging in the frame. The addition has settled slightly, throwing the rough opening out of square. It’s a symptom of the foundation, not the hinge.
- Drafts or visible light at the perimeter of a window. The weather seal has failed, and the window is now a heat path in an Arlington summer.
- Roof shingles lifting or granules collecting in the gutter on the addition side only. The roof-to-wall transition has lost its closure, and the shingles there are taking wind load they weren’t meant to carry.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a single component replacement on an Atlas addition, expect to spend a fraction of the full-build range above. Installed pricing for a door or window swap typically runs $800 to $3,200 depending on the size and whether trim repair is needed. A flashing re-seal at the roof tie-in is $400 to $1,800. Foundation shim and pier work runs $2,500 to $9,000 if the frame is involved.
What drives the number: whether we can source an exact-match part or need to fabricate, how much interior finish has to come apart to reach it, and whether permits are required (they usually are on foundation work in Arlington, and we pull them). Every scope, allowance, and price change arrives in writing before we start. You get the written quote, the parts identified by part number, and the 90-Day Done Right Promise in writing on the contract.
DIY or Call Us?
Some of this is owner-safe: you can measure the rough opening, photograph the data plate, check the shim under a pier with a flashlight, and confirm whether the sticking door is the door or the frame. That’s useful information to bring to a call. Where DIY goes wrong, and where we won’t walk you through it, is foundation and roof tie-in work. Lifting and re-shimming an addition frame without the right equipment can turn a $3,000 repair into a $30,000 problem, and getting on an addition roof to re-flash is a fall hazard most folks shouldn’t take on. Our technicians have up to 28 years of experience with exactly this kind of structural work. Call (888) 590-9867 and we’ll tell you honestly which category your repair falls into.
FAQs
How long should an Atlas addition component last in Arlington weather? Door and window parts typically last 15 to 25 years in this climate, but flashing and sealant at the roof tie-in should be inspected every 5 to 7 years because Texas heat and hail degrade them faster than the parts themselves.
Can this be repaired instead of replaced? Often yes – a shim can be re-set without replacing the pier, and flashing can be re-sealed without a new roof section. The repair decision depends on whether the underlying framing has moved, and we’ll tell you which one you’re looking at. Call (888) 590-9867 for a free second opinion on any written estimate you’ve already received.
How long does the swap take? A window or door replacement is a one-day job. Flashing re-seal is typically half a day. Foundation shim and pier work runs 2 to 4 days depending on access and how many piers are involved.
How do you source the part? We identify the series from the data plate, order the OEM part where it’s a load-bearing or sealing component, and quote an exact-match aftermarket equivalent when the OEM is discontinued. We don’t stock parts on a truck – every part is ordered to your unit, and we tell you the part number before we order.
If your Atlas addition or ADU part has failed, the fastest way to know whether it’s a $400 fix or a $4,000 one is to have someone look at it. Call Barrett & Sons Construction Arlington at (888) 590-9867 to schedule your free estimate. We pull the permits, we put the price in writing, and the 90-Day Done Right Promise is on every contract.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.