Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Kitchen Remodeling: The Arlington Owner’s Guide
In Arlington, kitchen remodeling projects with Barrette cabinetry and millwork typically run $14,000 to $45,000 installed, and a cabinet, door, or millwork component failure is usually addressed within a scheduled visit, not a same-day trip. If a Barrette door is sticking, a drawer box has cracked, or a hinge plate has pulled from the cabinet frame, the practical path is a measured replacement matched to your exact Barrette line and finish, not a universal part. Call (888) 590-9867 for a free estimate on the correct scope.
Most Arlington homeowners find us after noticing a soft, sagging drawer bottom or a door that won’t stay shut once the humidity climbs. Those symptoms look minor until you open the cabinet and see the damage underneath: cracked plywood, stripped screw holes, a hinge pulling out of the frame. That’s the point where the part matters more than the polish.
Quick takeaways:
- Installed kitchen range in Arlington: $14,000 – $45,000.
- Cabinet installation alone: $4,000 – $13,000.
- Countertop replacement: $2,000 – $6,500.
- Backsplash: $800 – $2,500.
- Barrett & Sons is an independent contractor and not affiliated with Barrette.
Which Barrette Models This Applies To
Barrette cabinetry and millwork spans framed and frameless lines, and the part that fits one series will not fit another. The label inside the cabinet door or on the back of the drawer box is your starting point – that sticker carries the series, the finish code, and sometimes the width. Write it down before you call anyone. A photo of the label plus a tape measure across the door front and the drawer opening tells us more than a description ever will.
Two compatibility points trip up Arlington owners:
- Hinge pattern changes within a line. Barrette has revised hinge cup bore spacing over the years, and a replacement door cut for the older pattern will not align with newer frame drilling. Measure the bore spacing, don’t assume.
- Finish codes drift. The same “white” or “maple” name can cover two different production runs. A door pulled from a current catalog may read a shade off against cabinets installed a decade ago.
On the OEM-versus-aftermarket question: a factory Barrette replacement door or drawer box is the only way to guarantee an exact finish match. Quality aftermarket hardware (hinges, slides, shelf pins) is a reasonable substitute when the original hardware has been discontinued – brands like Blum and Grass make hardware that fits Barrette drilling patterns, and we’ll tell you plainly which way makes sense for your cabinet. We don’t claim to stock Barrette parts or carry them on a truck. We source them for your job.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Barrette Kitchen Remodeling Is Failing
Arlington’s summer heat and humidity work on wood cabinets the way they work on everything else here. The failures we see most often:
- A drawer bottom sagging or bowing. Usually a thin lauan or particleboard bottom that has absorbed moisture. In older cabinets the bottom was stapled, not dadoed, and once it swells it never lays flat again.
- Hinges pulling out of the frame or door. The screw holes strip when the door gets slammed or the cabinet swells. A hinge plate that’s migrated more than a sixteenth of an inch is telling you the wood around it is compromised.
- A door that rubs or won’t close flush. Often a hinge adjustment problem, but sometimes a warped door from a finish failure. Check whether the gap along the top is even before you touch the screws.
- Delamination or peeling veneer at the edges. Moisture gets behind the veneer at the door edge or under the sink and lifts it. Left alone, the substrate swells and the door is done.
- Cracked or split drawer boxes. Common in frameless cabinets where the box carries the load. A split at the corner joint means the box needs replacing, not regluing.
One pattern worth knowing: cabinets set against an exterior wall in an Arlington kitchen take more seasonal movement than cabinets on an interior wall, because the wall itself expands and contracts with the heat. If the failures cluster on one side of the kitchen, that’s the reason.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s the honest price picture for Arlington. These are installed ranges, not parts-only prices, because the labor is where the surprises live.
| Scope | Installed range |
|---|---|
| Full kitchen remodel (Barrette cabinetry) | $14,000 – $45,000 |
| Small kitchen remodel | $9,000 – $20,000 |
| Cabinet installation or replacement | $4,000 – $13,000 |
| Countertop installation | $2,000 – $6,500 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island installation | $3,000 – $10,000 |
What moves a job toward the top of the range: custom door sizes, a finish that requires a full run to match, countertop removal and reinstall, or plumbing and electrical changes behind the cabinets. Single-door or single-drawer replacements sit well under the cabinet range, and we quote them as a line item, not a package.
Every scope, allowance, and price change arrives in writing on a change order before work starts. No surprise invoices. Every eligible job is permitted and inspected, and the finished work is backed by our written 90-Day Done Right Promise.
DIY or Call Us?
Some of this an owner can check safely. Adjusting a European hinge with a screwdriver is fine. Tightening a loose cabinet pull is fine. Measuring a door and photographing the label is exactly what we’d ask you to do anyway.
Where it goes wrong: regluing a drawer box that has already delaminated, or forcing a replacement door onto a hinge pattern that doesn’t match, which cracks the frame and turns a $90 part into a $900 cabinet repair. If a cabinet is mounted over a gas line, a dishwasher connection, or an electrical junction box, don’t drill or pry near it – that’s a call to a licensed trade, and we’ll tell you so. Our crews have up to 28 years of experience and we’re insured and bonded. Call (888) 590-9867 for a free second opinion on any written estimate.
FAQs
Fifteen to twenty-five years is realistic for well-built cabinetry in this climate, with hardware (hinges and slides) usually failing first, around year eight to twelve.
Sometimes yes – a hinge adjustment or a new slide often fixes the problem, but a delaminated door or a split drawer box usually needs replacement. We’ll tell you which before you spend.
Once we have the correct part in hand, most single-component swaps run a few hours. Sourcing the right Barrette part is the variable, and we’ll give you a realistic timeline up front.
We match your label, series, and dimensions against the current catalog and, where original hardware is discontinued, against compatible aftermarket equivalents. Call (888) 590-9867 – estimates are free.
We also handle KraftMaid, Cambria, and Silestone cabinetry and countertop work when a Barrette match isn’t the right answer for your kitchen.
Read the full scope, the allowances, and the price in writing. Call (888) 590-9867 for a free estimate and a straight answer on your Arlington kitchen.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.