Home additions & ADU
Kitchen remodeling
Bathroom remodeling
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Home Additions & ADU: The Arlington Owner’s Guide
When a Boral-clad addition or ADU starts failing on an Arlington home, the fix is almost never a whole new structure. It’s the specific failing component – a cracked cladding panel, a leaking roof-to-wall joint, a moisture-wicking flashing, or a shifting trim line – and the parts-and-labor repair runs $45,000 – $130,000 for a full addition rebuild or $90,000 – $220,000 for a full ADU, with component-level fixes often falling well below the low end. We can’t offer same-day availability on structural work, but we do start with a free written estimate, usually within a few business days of your call.
Owners in Arlington typically catch a failing Boral assembly the same way: a hairline crack that reappears after every caulking, a soft spot under a window where the flashing was stepped wrong, or a stain line at the ceiling edge that shows up first thing after a June thunderstorm. Boral’s cladding and trim products are tough, but Texas heat cycles and clay soils don’t forgive a detail that was missed at install. The part matters, and so does how it’s tied in.
Key Takeaways
- Boral repair and rebuild work in Arlington runs $45,000 – $130,000 for additions and $90,000 – $220,000 for a full ADU.
- We’re an independent contractor, not affiliated with Boral – we’ll source the right component for your model.
- Every eligible job has permits pulled and inspections signed.
- The 90-Day Done Right Promise is written on every contract.
Which Boral Models This Applies To
Boral’s residential exterior line covers a lot of ground, and the part that failed depends entirely on which product your addition or ADU was built with. The most common assemblies we see on Arlington additions are Boral Versetta Stone panels (mortarless, mechanically fastened), Boral TruExterior Siding & Trim (a poly-ash composite often used around ADU door and window surrounds), and Boral Cultured Stone veneer where a homeowner wanted a masonry look without full brick. Each has its own fastening schedule and thermal movement spec, and mixing the wrong fastener or clip into the wrong panel is the single most common install failure we correct.
To identify what you have, look for the manufacturer label on the back of a loose panel or on the packaging that may still be in the garage, then measure a panel face and note the profile. Versetta Stone panels run in fixed face heights and lengths, and ordering a matching profile by eye alone is where homeowners get burned – a near-match profile will telegraph through a repaired wall once the sun hits it.
On the OEM-versus-aftermarket question: Boral’s own replacement clips and accessories are spec-matched to their panels and are the safe call for any visible face repair. For hidden fasteners, flashing, and sealants, quality aftermarket equivalents are fine if they meet the same corrosion and movement spec. State it plainly: we install Boral-compatible additions and ADU work as an independent contractor – we’re not affiliated with Boral, but we know the product line and we’ll match the part to your model before we quote.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Boral Home Additions & ADU Is Failing
- A crack that keeps coming back after caulking. Caulk bridges the symptom, not the cause – a crack that returns within a season usually means a fastener or clip has backed out and the panel is moving under thermal load.
- Staining or a chalky line at the ceiling or wall edge. Water is getting behind the cladding and running down an interior surface. It usually traces to a flashing that was lapped the wrong direction or a missing weep detail.
- Soft or spongy trim around windows and ADU doors. Poly-ash trim will absorb moisture at an end cut that wasn’t sealed. Once it swells, the paint film fails and the rot spreads fast.
- Rattling or visible gapping on a windy day. Fasteners have loosened or the wrong length was used. On a Boral panel assembly, a rattling face is one good hail storm away from a panel on the ground.
- Efflorescence or white bloom on stone veneer. Moisture is trapped behind the veneer and pushing salts to the surface. Left alone, it eats the mortar bed and the panel bond.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For an Arlington home addition, expect $45,000 – $130,000 for a full rebuild or a major structural repair with new Boral cladding. A full ADU rebuild or new ADU shell runs $90,000 – $220,000, and a garage-to-ADU conversion sits at $30,000 – $80,000. Component-level repairs – a re-flash, a panel replacement run, a trim section – fall well inside those ranges and are quoted line by line.
What drives the number: whether the framing behind the Boral is sound, how much of the cladding field has to come off to reach the failure, and whether the fix needs a permit and inspection. Every scope, every allowance, and every price change arrives as a written change order before the work happens. Permits are pulled and inspections signed on every eligible job. The labor and workmanship carry the 90-Day Done Right Promise – written on the contract, not buried in fine print.
DIY or Call Us?
An owner can safely inspect. Walk the perimeter, look at the bottom edge of the cladding for gaps, check window and door surrounds for soft spots, and photograph any crack line with a tape measure in frame. That’s information we’ll use to quote accurately.
What you shouldn’t do: remove a panel from the field to “see what’s behind it,” re-flash a wall-to-roof joint, or re-fastener a Boral panel assembly yourself. The cladding is the weather barrier’s outer shield, and once it’s off, water gets in faster than you can get it back on. On any addition or ADU, pulling the wrong fastener or resetting a panel without matching the correct clip can compromise the whole wall’s water resistance and void what remains of the original install. That’s not a do-it-yourself repair – it’s a licensed scope with a permit.
Call (888) 590-9867 and we’ll walk the problem with you, free of charge.
FAQs
Installed correctly, Boral’s cladding and trim lines are built for 30-plus years of service, and the poly-ash trim carries a long manufacturer warranty against rot and termite damage. In Arlington’s heat and clay, the failure comes from install details – flashing, fasteners, end-cut sealing – not from the product itself. Call (888) 590-9867 for an exact quote – estimates are free.
Yes, in most cases. A local re-flash, a panel run replacement, or a trim section swap is a component repair, not a rebuild, and it’s priced accordingly. The only time the answer is “replace” is when the framing behind the cladding has taken on moisture damage. We’ll tell you which one you’re looking at after the inspection.
A component repair typically takes one to three days on site; a full reconstruction or ADU shell is a multi-week job with a written schedule. Weather, permit timing, and material lead time on the specific Boral profile all affect it, and we won’t quote a schedule we can’t hold.
We identify your Boral model from the panel labels and measurements, then order through Boral’s distribution network so the profile and fastening spec match what’s on your wall. On hidden fasteners and sealants we use spec-matched aftermarket equivalents where they’re equal to or better than OEM. We don’t carry parts on a truck – it’s ordered for your job.
We’re Barrett & Sons Construction Arlington, an independent contractor and not affiliated with Boral. We also work with KraftMaid, Cambria, and Silestone on the interior side. Call (888) 590-9867 to schedule your free estimate – a live person answers, 24 hours a day.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.