Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Kitchen Remodeling: The Arlington Owner’s Guide
Boral manufactures engineered stone and cultured marble surfaces, and in a kitchen the pieces that matter most are the countertop, the island top, and the backsplash. When an owner tells us a Boral surface has failed, it’s almost always a hairline crack radiating from the sink cutout, a chip at a cabinet corner, or a dull, etched patch where hot grease or a hot pan sat too long. We’re an independent construction company, not affiliated with Boral, and we install Boral surfaces alongside KraftMaid cabinets and Cambria and Silestone tops. Full Boral kitchen remodels in Arlington typically run $14,000 – $45,000, with a countertop-only swap landing in the $2,000 – $6,500 range.
Which Boral Models This Applies To
Boral’s kitchen surface lines don’t carry model plates the way a garage door opener does, so identifying your piece means reading the material, not a serial number. Look under the countertop overhang near the dishwasher; installers often leave a fabricator sticker or a manufacturer stamp there. Boral cultured marble tops are a polyester-resin and stone-dust mix poured in a mold with a gel-coat surface, while Boral engineered stone is a pressed slab. That distinction decides your replacement path, because the two fail differently and repair differently.
Here’s the compatibility gotcha that trips people up: cultured marble tops are cast to a specific counter depth and edge profile, and a replacement piece from a different production run will not match the veining on your remaining sections. If your kitchen has three countertop runs and only the sink run is cracked, we check the gel-coat color name printed on that fabricator sticker before ordering. Engineered stone has its own trap – slab thickness. Boral slabs in 2 cm and 3 cm are both common, and an Arlington cabinet run built for 3 cm won’t accept a 2 cm top without a build-up strip, which changes your edge detail.
On the OEM-versus-aftermarket question: Boral parts and slabs are orderable through authorized fabricators, and quality equivalents exist in the same thickness and finish family. We quote both, in writing, so you can see what the brand name costs you. Our crew members have up to 28 years of experience reading these specs off a counter.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Boral Kitchen Remodeling Is Failing
Most owners discover the problem the same way – a cup of coffee set down on a warm morning, and a crack that wasn’t there yesterday. Watch for these:
- A hairline crack starting at the sink or cooktop cutout. The cutout is the thinnest, weakest span in any countertop, and the stress concentrates there first. On Boral cultured marble, a crack means the resin has given up locally and a matching repair is a stopgap, not a fix.
- Chips at outside corners and edges. Cultured marble gel-coat chips when a heavy pot catches the edge or a cabinet door swings into it. Small chips can be color-matched and filled; a chip that reaches the substrate usually means the edge needs rebuilding or the piece needs replacing.
- Dull or cloudy patches that won’t polish out. This is chemical etch, common when acidic cleaners or hot oil sit on a polyester surface. Engineered stone resists it far better than cultured marble, which is why we steer Arlington kitchens with heavy cooking toward slab.
- A seam that has darkened or lifted. Seam failure near a dishwasher or sink points to moisture getting under the edge, and it usually means the substrate below is soft. Sound the area with a knuckle before you order a new top.
- The counter moves or rocks under hand pressure. A top that rocks is resting on a failed or unlevel cabinet run, not a failed countertop. Replacing the surface alone won’t stop it, and this is where a written scope saves you money.
In Arlington, we see more edge chipping in older kitchens where a cast-iron skillet lives on the counter and gets set down hard on the corner, and more seam lifting in homes where the dishwasher vents right into an under-counter seam.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed countertop pricing for Arlington, based on what we quote and write into a contract:
| Scope | Installed range |
|---|---|
| Countertop installation (Boral or equivalent) | $2,000 – $6,500 |
| Cabinet installation under a failing run | $4,000 – $13,000 |
| Backsplash installation | $800 – $2,500 |
| Kitchen island installation | $3,000 – $10,000 |
| Full kitchen remodel | $14,000 – $45,000 |
| Small kitchen remodel | $9,000 – $20,000 |
The low end assumes one counter run, standard edge, and existing cabinets that are sound. The high end reflects multiple runs, an island, a cutout for an undermount sink, and a backsplash. What drives it: square footage, edge profile, number of cutouts, and whether the cabinet run underneath needs leveling or replacement. Materials and labor are line-itemed separately, so you see exactly what the Boral surface costs versus what the install costs. Every eligible job gets permits pulled and inspections signed, and the work carries our written 90-Day Done Right Promise – if something’s wrong, Tom comes back and makes it right, one call.
DIY or Call Us?
You can safely check for a fabricator sticker, measure your counter depth, photograph the crack and the seam, and sound the substrate with a knuckle. That information saves you time on the phone and usually narrows the repair to one run.
What you shouldn’t do is lift a countertop yourself. A Boral surface is heavy, mounted over cabinets, plumbed at the sink, and often wired to a disposal. Pulling it without shutting the water off and disconnecting the plumbing risks water damage to the cabinet run and a two-person lift that’s genuinely dangerous alone. Cutting or grinding engineered stone also releases silica dust, which you don’t want in your kitchen without proper respiratory protection. That’s a job for a crew with the right gear.
Our crew members carry the Barrett & Sons name and are background-checked and uniformed on every visit. Call (888) 590-9867 for a free estimate and we’ll tell you straight whether you need a repair or a replacement.
FAQs
How long does a Boral countertop last? A properly installed Boral cultured marble top lasts roughly 10 to 15 years in a normal kitchen, and engineered stone lasts considerably longer with basic care. In Texas heat and humidity, the weak point is usually the seam and the sink cutout, not the surface itself. Call (888) 590-9867 for an exact quote – estimates are free.
Can a Boral countertop be repaired instead of replaced? A chip or small crack can often be filled and color-matched for a fraction of a replacement, and we’ll tell you honestly when that’s the right call. A crack that reaches the substrate or a lifted seam usually means replacement is the cheaper answer over time. Call (888) 590-9867 and we’ll look at photos before you commit.
How long does a countertop swap take? A single-run Boral countertop replacement typically takes one to two days, including tear-out and reinstall, with the sink disconnected and reconnected on the same visit. Full kitchen remodels run weeks, not days, and we schedule those in writing. Call (888) 590-9867 for a timeline you can plan around.
How do you source the replacement part? We order Boral slabs and cast pieces through authorized fabricators, and we quote a quality equivalent side by side so you can compare cost and finish. If your original gel-coat color is discontinued, we’ll show you the closest match before anything is ordered. Call (888) 590-9867 for a free second opinion on any written estimate you already have – it costs you nothing but a phone call.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.