Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Dvele Driveway & Pavers: The Arlington Owner’s Guide
A paver driveway or patio at a Dvele-built home in Arlington can be reset or repaired in most cases, and a full installation runs roughly $7,000 – $18,000 for paver work and $250 – $700 for sealing, depending on square footage, base condition, and pattern. Barrett & Sons Construction Arlington is an independent installer and service provider, not affiliated with Dvele, so we work to the material spec and the site, not to a factory service script.
Owners usually catch the problem after a hard rain or a freeze-thaw week. Sand starts washing out of the joints. A field of pavers near the garage apron sits a half inch lower than it did last spring. Or a paver pops loose and rocks underfoot when the mower rolls over it. That loose-and-rocking feeling is almost always a base problem underneath, not the stone itself, and it shows up in Arlington clay more than owners expect.
Key takeaways
- Most Dvele paver failures we see in Arlington are base and drainage issues, not bad pavers.
- Reset and re-sand work is often a fraction of full replacement when the stone is sound.
- Polymeric sand, not plain mason sand, is the joint standard we install in North Texas.
- Sealing is maintenance, not a fix. It won’t correct a failing base.
Which Dvele Models This Applies To
Dvele builds a range of panelized and modular homes, and the hardscape package varies by plan and by build year. We’ve worked across the more common configurations, and the stone and joint spec is rarely identical between two Dvele homes even a few streets apart in Arlington. The plan set and the original hardscape drawings are the fastest way to match what you have.
Here’s how to identify your spec before you order anything:
- Find the plan set. Dvele owners usually receive a construction and finish document set at closing. The hardscape page lists paver series, thickness, and laying pattern.
- Measure a sample paver. Dvele hardscape commonly uses 60mm or 80mm thick units in a standard modular footprint. Thickness matters if you’re patching a section; a 60mm unit in an 80mm field shows as a lip.
- Photograph the pattern. Herringbone, running bond, and ashlar all read fine in a photo but interlock differently at edges. Send us the photo and we’ll match the laying pattern, not just the color.
On the OEM question: pavers are a commodity product, not a proprietary Dvele part. Belgard and Techo-Bloc both make series that match or exceed the original spec, and they’re verifiable brands with published technical data. If the original series is discontinued, which happens more than folks realize, an equivalent color and thickness from a named manufacturer is the right move. We don’t stock pavers and we don’t carry them on a truck. We spec the match and bring the material to the job.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Dvele Driveway & Pavers Is Failing
Arlington sits on expansive clay soil that swells when wet and shrinks in summer drought. That movement is hard on any hardscape, and it’s the root cause behind most of what owners describe to us. Here are the five we see most.
- Sand washing out of the joints after rain. Plain mason sand migrates with water. When it keeps coming back after every storm, the joints need polymeric sand and the drainage needs a look.
- Pavers rocking or loose underfoot. The bedding layer has lost contact with the paver. This is a base or settling problem and it spreads if you leave it.
- Sunken field near the garage apron or driveway edge. The transition zone carries the most load and takes the most water. A dip there is usually a base compaction issue.
- Efflorescence, a white chalky haze on the surface. Mineral salts wicking up from the base. It can be cleaned, but recurring haze points to moisture trapped under the pavers.
- Weeds and moss pushing up between units. Not just cosmetic. It means the joint sand has failed and water is getting where it shouldn’t.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what paver work runs in Arlington, installed, with the material and labor bundled so you can compare apples to apples:
| Job | Installed range |
|---|---|
| Paver driveway installation | $7,000 – $18,000 |
| Driveway replacement | $5,000 – $14,000 |
| Paver patio installation | $3,500 – $11,000 |
| Driveway sealing | $250 – $700 |
| Concrete driveway installation (comparison) | $4,500 – $12,000 |
What moves the number: total square footage, how much base has to be excavated and recompacted, whether an edge restraint is missing or failing, and the paver series you choose. Where the base is sound and only a section has failed, a reset and re-sand is often a fraction of a full install and we’ll tell you plainly which one you need.
Every job gets a written scope, written material allowances, and a written change order before any work proceeds. Nothing gets added to the invoice after the fact. The completed work is covered by the written 90-Day Done Right Promise.
DIY or Call Us?
There’s a real split here, and it depends on what’s actually wrong. An owner can safely sweep and top off joint sand, pull weeds, and use a paver sealer on a sound, settled surface. That’s maintenance and it’s fine to do yourself.
Where DIY goes wrong is the base. Pulling up pavers to “just re-level” a sunken section without recompacting the bedding and checking the drainage underneath means the dip returns by the next wet season. Reset work without an edge restraint is the same story a few months down the road. If pavers are moving more than a quarter inch underfoot, or the dip is at a driveway transition where a vehicle loads it, that’s beyond a weekend fix. We’ll tell you honestly whether it’s a reset or a rebuild instead of selling you the bigger job. Call (888) 590-9867 and we’ll look at it with you.
FAQs
A properly installed paver driveway holds up for decades, but in Arlington’s clay soil the number that matters is the base, not the stone. A well-compacted, well-drained base can serve 25 years or more. A base laid over unprepared clay can start failing inside three to five seasons of wet-dry cycling. Polymeric sand joints and periodic sealing are what stretch the life on the front end.
Often yes. If the individual pavers are sound and the failure is isolated to a sunken field or failed joints, a reset of that section with fresh bedding and polymeric sand costs far less than a full replacement. Full replacement makes sense when the base is failing across the whole driveway or the pavers themselves are cracked and crumbling. Call (888) 590-9867 for a free estimate and we’ll tell you which one your driveway needs.
A small section reset is typically a one-day job. A full paver driveway installation in Arlington usually runs three to five days, weather depending, including base prep, laying, edge restraint, and joint sand. We schedule it out and give you the timeline in writing before we start.
We match the manufacturer, series, thickness, and color from your Dvele plan set, then verify the spec against Belgard or Techo-Bloc technical sheets. If the original series has been discontinued, we find an equivalent in the same thickness and footprint so the new section blends with the existing field. You’ll see the material and the allowance in writing before we order a single unit.
We work across the trades Dvele owners run into, including KraftMaid, Cambria, and Silestone on the interior side, plus every exterior job from roofing to fence. Same written scope, same written change orders, same 90-Day Done Right Promise.
If your paver driveway in Arlington is washing out, settling, or just past its prime, we’d rather look at it and give you an honest read than have you guess. Barrett & Sons Construction Arlington is owner-operated, every eligible job gets its permits pulled and inspections signed, and every price change arrives in writing before work starts. Our crew members have up to 28 years of experience, and our standing offers include $40 Off Any Repair Over $200, a Free Second Opinion on Any Written Estimate, No Trip Charge Inside the County, and a permanent 10% Senior & Veteran discount. Call (888) 590-9867 for a free estimate and we’ll get you a written scope you can actually compare.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.