Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
IKO Fence Installation: The Arlington Owner’s Guide
IKO fence installation in Arlington runs $3,500 – $9,000 installed for a typical residential yard, and the price depends mostly on linear footage, gate count, and how much old fence has to come out first. We don’t rush planned fence work, but we do give you a written line-item quote and a real start date, not a maybe. Most Arlington homeowners call us after a windstorm peels a panel loose or they notice a post that’s gone soft at the base while the rest of the fence looks fine.
Here’s the thing about IKO: they’re known for roofing underlayment and shingles, and the IKO name shows up on fencing mostly through the accessory side of the trade, not as a big standalone fence-panel brand. So when you tell us you have an “IKO fence” issue, the first job is figuring out what’s actually on your property. That’s why we ask for a photo before we talk price.
Key Takeaways
- Typical installed IKO-compatible fence in Arlington: $3,500 – $9,000.
- We’re an independent contractor, not affiliated with IKO.
- Wind and clay soil are the two biggest reasons fences fail here.
- Written change orders before any scope change, every time.
- Call (888) 590-9867 for a free estimate.
Which IKO Models This Applies To
IKO’s product line is deep on the roofing side – Dynasty, Cambridge, Nordic – and thinner on the fencing side, which is the compatibility gotcha most Arlington homeowners run into. What you likely have is either an IKO-branded post or rail component, an IKO fence accessory like a bracket or cap, or a fence put up by a contractor who used IKO materials on the roof and the homeowner assumed the fence matched. It pays to check the label before you buy a replacement.
To identify what you’ve got, look for a stamp or sticker on the post or rail, usually within six inches of the bottom or top. Measure the post width (most residential is 4×4 or 5×5 nominal) and the rail thickness. If there’s no label, take a photo with a tape measure held against the rail and send it over. We’ll tell you whether it’s an IKO component or a standard pressure-treated or cedar piece that a compatible replacement will fit.
For IKO-specific parts, OEM replacement is the safe call because the dimensional tolerances on IKO fence accessories are tighter than generic equivalents. A quality aftermarket bracket can work, and we use them when the OEM is backordered, but the fit isn’t always the same. When we quote, we tell you which one we’re using and why. Our crew members have up to 28 years of experience with both. We also handle KraftMaid, Cambria and Silestone on the remodel side, but that’s a different conversation.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your IKO Fence Installation Is Failing
North Texas weather is hard on fencing. Between the clay soil that swells and shrinks with every wet-dry cycle and the spring wind gusts that hit 40-plus mph in Arlington, fence failures here tend to show up in the same places year after year.
- Leaning or wobbling posts. The post has pulled loose from its concrete footing, usually because the footing was set too shallow or the soil shifted after a wet spring. In Arlington, we see this most on fences set in the blackland clay on the west side of town.
- Loose or separated panels. Wind caught a panel and popped the fasteners or shifted the rail out of the bracket. If the panel is still whole, this is often a bracket-and-fastener fix rather than a full replacement.
- Rot at the base of posts. Water pools at the soil line and untreated or under-treated wood soaks it up. Check by pressing a screwdriver into the post six inches above grade; if it sinks easily, the post is done.
- Rust streaks or corrosion on metal components. Galvanized hardware in a coastal-humidity pattern (which Arlington gets in spades) can start showing surface rust within a few seasons. Surface rust on a bracket isn’t a failure; structural thinning is.
- Gates that drag or won’t latch. Usually a hinge or post-sag issue, not the gate itself. It’s the most common call we get and usually the cheapest to fix.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed IKO-compatible fence work in Arlington typically runs $3,500 – $9,000 for a standard residential yard. What drives the range: linear footage (most yards are 150 – 250 feet), gate count, material selection (pressure-treated pine versus cedar versus composite), and whether we’re removing the old fence and hauling it off. Post replacement alone is a smaller line item and we quote it separately.
Every quote is written line-item, so you see materials, labor, disposal, and permits (where required by the City of Arlington) as separate lines. No surprise invoices. If we open up the fence and find the footer is worse than expected, you get a written change order before we touch it. Repairs over $200 get $40 off, and there’s no trip charge inside Tarrant County. All fence work is backed by our written 90-Day Done Right Promise: if it’s not right, one call brings us back.
DIY or Call Us?
Some fence work is genuinely homeowner-friendly. Tightening hinge screws, replacing a bracket, resetting a gate latch, touching up surface rust with a wire brush and paint – all fine to do yourself, and we’ll happily talk you through it on the phone.
Where DIY goes wrong is anything structural. Post replacement sounds simple, but a leaning post usually means the footer failed, and resetting it right means digging below the frost line, setting proper concrete, and bracing until it cures. Get that wrong and you’ve got a post that leans again by the next wet spring. Wind-damaged panels are the same story: if the underlying rail or bracket is compromised, a new panel just delays the failure. Anything that involves a post in the ground or a section of fence under tension, call us.
Call (888) 590-9867 for a free estimate.
FAQs
How long should an IKO fence in Arlington last? A properly installed pressure-treated fence lasts 15 – 20 years in North Texas; cedar runs 15 – 25; composite goes 25 – 30. The single biggest lifespan variable here is the footer depth and soil drainage, not the brand of wood.
Can a failing fence be repaired instead of replaced? Often, yes. Individual posts, panels, rails, and gates can usually be swapped without touching the rest of the run. If more than a third of the posts are soft, full replacement usually pencils out better. Call (888) 590-9867 and we’ll tell you honestly which one makes sense.
How long does the swap take? A single post or panel is a half-day job. A full residential fence replacement in Arlington is typically 2 – 4 days depending on linear footage and gate count. Weather adds a day if we hit rain.
How do you source the IKO part? We order through IKO’s standard distribution channels and confirm the model before we order. If the exact IKO component is backordered, we tell you and quote a compatible alternative with the specs side-by-side.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.