Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Mr-Glass Fence Installation: The Arlington Owner’s Guide
Fence installation on Mr-Glass systems around Arlington usually runs $3,500 to $9,000 installed, depending on run length, gate count and panel layout, and most single-run jobs are finished in a day or two once the parts and permits are in hand. When a Mr-Glass fence starts to fail, owners rarely notice the fence itself first. They notice the gate that catches on the latch handle, the post that wobbles when the wind gusts off the Trinity flats, or the bottom rail that suddenly looks bowed from the sidewalk. Our crews have up to 28 years of experience working with premium fence systems, and this guide covers what we see on Mr-Glass jobs across Arlington.
One thing to be clear on up front: Barrett & Sons Construction Arlington is an independent contractor, not affiliated with Mr-Glass. We install and repair these systems, and we’ll match the correct part to your model without claiming to be the manufacturer.
Key Takeaways
- Mr-Glass installs around Arlington typically land between $3,500 and $9,000 for a full run, with gate hardware and grading as the biggest swing factors.
- Most early failures we see in North Texas trace to footing movement in the expansive clay soils, not to the panels themselves.
- OEM panels and rails are the right call for color and profile matching; aftermarket is fine for hardware and fasteners if the gauge matches.
- Every scope and price change arrives in writing before work starts, backed by the 90-Day Done Right Promise.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Which Mr-Glass Models This Applies To
Our crews work across the Mr-Glass residential fence lines, and the identifying details matter because panel profiles and rail caps changed between series. Before we order anything, we ask owners to check three things. Look for the model or series stamp on the inside face of a post or on the rail end cap; if there’s no stamp, measure the panel height and the post spacing, since a half-inch difference in post spacing changes which brackets fit.
The OEM-versus-aftermarket decision splits cleanly on Mr-Glass systems. Go OEM for panels, rails and post caps, because color runs and profile extrusions differ enough between production years that an aftermarket panel will show line-of-sight against the original. Aftermarket is fine for gate hinges, latches, screws and footing hardware, as long as the gauge and finish match what’s on the fence now. We don’t carry parts on a truck or hold stock. The part gets sourced to your model, and we tell you in writing which parts are OEM and which are aftermarket before we order.
Signs Your Mr-Glass Fence Installation Is Failing
- Gates that drag or won’t latch. The hinge hardware has loosened or the gate post has settled, which pulls the gate out of square. In Arlington we see this most on posts set near sprinkler lines.
- Wobbly or leaning posts. The footing has lost grip in the expansive clay common across Tarrant County. The post itself is usually fine; it’s the soil movement doing the work.
- Panels that look bowed or racked. A settled rail or a shifted bracket is holding the panel out of line. Left alone, the stress migrates to the next panel down the run.
- Loose top rails and caps. Fasteners have backed out from thermal cycling, and North Texas summers push that hard. Caps come off next if it isn’t caught.
- Rust streaks or finish failure at joints. Moisture is sitting where cut ends weren’t sealed. This shows up fastest on the weather side and near the bottom rail.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For an Arlington Mr-Glass installation or a failing-section rebuild, expect $3,500 to $9,000 for a typical residential run. What drives the range: linear footage, gate count, whether footings need re-digging because of soil movement, and how much of the existing fence can be reused instead of replaced.
| Item | Arlington range |
|---|---|
| Full vinyl/polymer fence install (comparable system) | $3,500 – $9,000 |
| Aluminum fence install (for comparison) | $4,000 – $10,000 |
| Mr-Glass repair or section rebuild | Quoted line by line |
Parts and labor show up as separate lines on the estimate, and any change to scope or parts arrives as a written change order before work happens. Permits get pulled and inspections signed where the work requires it, and every job carries the written 90-Day Done Right Promise.
DIY or Call Us?
An owner can safely check a lot of this: look for the model stamp, measure post spacing, tighten visible hinge screws with a hand driver, and note which panels move when you press on them. That information helps us quote accurately.
Where DIY goes wrong on Mr-Glass is at the footing and the gate alignment. Pulling a set post out of Arlington’s clay and getting a new one plumb, to depth, with the right concrete and the correct bracket alignment, is the step most owners regret. A gate that hangs out of square will rack the panels beside it within a season. That’s the point to call. Reach us at (888) 590-9867 and we’ll talk through what you’re seeing.
FAQs
A well-installed Mr-Glass fence should hold 20 years or more on the panels and rails, though hardware and footing performance run shorter in North Texas because of soil movement and summer heat cycling. Posts near irrigation lines and low-lying spots tend to be the first to show problems.
Yes, and often it should be. If the panels and rails are sound and the problem is a settled post or loose gate hardware, a targeted repair usually costs far less than a full run. We’ll tell you plainly which path makes sense after we look at it.
A single failing section or gate hardware swap is typically a one-day job once the correct parts are in hand, and a full residential run usually takes two to three days depending on footage and gate count. Sourcing OEM parts is often what sets the schedule, so we confirm that early.
We identify the model from the stamp or from measured post spacing and panel dimensions, then source OEM parts to match or aftermarket hardware of matching gauge and finish. You’ll see which is which in writing on the estimate before we order. Call (888) 590-9867 for a free estimate, and we’ll walk you through it.
If your Mr-Glass fence is leaning, dragging at the gate, or showing loose rails, don’t wait for the next panel to go with it. Barrett & Sons Construction Arlington installs and repairs these systems across Arlington and the surrounding communities, with scope and parts written down, permits pulled where required, and the 90-Day Done Right Promise behind the work. We also handle KraftMaid, Cambria and Silestone on the remodeling side if you’re working through a larger project. Call (888) 590-9867 to schedule your free estimate.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.