Bathroom remodeling
Kitchen remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Owens Corning Bathroom Remodeling: The Arlington Owner’s Guide
Owens Corning doesn’t make a bathroom “part” you swap out at the hardware store – it makes the materials inside the wall and under the floor: fiberglass insulation, the pink foam sheathing board, and mold-resistant drywall. When a bathroom is redone with Owens Corning materials and something fails years later, the culprit is almost always water, not the product. Owners in Arlington usually spot it as a soft, swollen spot under the tile, a pink fiberglass batt sagging out of a ceiling cut, or a shower wall that stays damp for days after every use. A full bathroom remodel in Arlington runs $9,000 – $28,000 when the wall and floor have to come open to fix what’s behind them.
Which Owens Corning Materials and Systems Apply Here
Owens Corning’s bathroom-relevant products break into a few lines: PINK Next Gen fiberglass batt insulation (an R-value printed on the facing or wrapper – R-13 and R-15 for 2×4 walls, R-19 and R-21 for 2×6), Foamular XPS rigid board for exterior-facing walls, and moisture-resistant gypsum board for wet areas. The compatibility gotcha is depth: an R-15 batt compresses into a standard 3.5-inch wall cavity, but a 2×4 wall behind a tile backer board often can’t hold it without the right batten and a careful vapor strategy, and the wrong stack-up traps moisture. Identify what you have by reading the R-value on the wrapper and reading the board’s edge print. For replacement, Owens Corning-branded material is the exact-match option; a quality equivalent is fine when specs match and the install details are done right. We install Owens Corning-compatible materials as an independent contractor, not affiliated with Owens Corning.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Owens Corning Bathroom Remodeling Is Failing
- Soft or bouncy floor tile. Water has reached the subfloor around a drain or toilet flange, swelling the wood under the backer board – the tile is the symptom, not the cause.
- Pink insulation sagging out of a ceiling cut. A roof or vent leak has soaked the batt; wet fiberglass loses performance and grows musty fast in a Texas attic.
- Grout cracking along a shower corner. Movement or water behind the wall is pushing the joints apart, usually where the pan meets the wall.
- Musty smell that comes back after cleaning. Moisture trapped inside the wall assembly with no path out; the drywall is holding it.
- Bubbling or peeling paint at the base of a wall. A slow supply-line or tub-overflow leak saturating the wall from the bottom up.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
A full bathroom remodel in Arlington runs $9,000 – $28,000. A small bathroom lands at $5,000 – $12,000; a walk-in shower installation is $4,500 – $12,000, and a tub-to-shower conversion $3,500 – $10,000. What drives the range is how much has to come open: opening a wall to replace wet insulation and board costs more than a surface refresh. A vanity install runs $800 – $3,000. Every line item is priced in the written scope before work starts, and any change arrives as a written change order first – no surprise invoices. The finished work is backed by the 90-Day Done Right Promise.
DIY or Call Us?
You can safely check the obvious: read the R-value on your insulation wrapper, run a flashlight along the base of the shower wall, and press the floor near the toilet for softness. Where DIY goes wrong is opening a wet wall – cutting into a shower pan or an exterior wall without knowing where the vapor barrier and waterproofing sit means trapping moisture all over again, and a small leak can turn into a rot repair. If water has reached the framing, call. Call (888) 590-9867 for a free estimate; a live person answers around the clock.
FAQs
How long does Owens Corning bathroom material last? The insulation itself lasts decades if it stays dry. Fiberglass and XPS board only fail early when water gets at them – the material is fine, the moisture path is the problem.
Can the damaged area be repaired instead of remodeled? Often yes. If the wet patch is isolated, we can open the affected section, replace the insulation and board, dry it out, and close it. If the rot has spread into framing, a fuller remodel makes more sense. Call (888) 590-9867 for a free estimate to find out.
How long does the swap take? A targeted wall-and-insulation repair is a few days. A full bathroom remodel in Arlington runs about two to four weeks, depending on finish and inspection scheduling. Permits are pulled and inspections signed on every eligible job.
How do you source the Owens Corning material? We specify the matching product by R-value and board type and buy it through standard supply channels – nothing is claimed as stocked or carried. We quote material and labor separately so you can see what you’re paying for. Brandt-depth brands across other rooms include KraftMaid, Cambria, and Silestone.
Call (888) 590-9867 for a free estimate.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.