Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
PGT Windows & Doors: The Arlington Owner’s Guide
We repair and replace failed PGT windows and doors across Arlington, and a typical installed job runs from about $450 to $2,500 depending on whether you need a part swap or a full unit. Full window replacement in Arlington generally falls between $4500 and $15000, and impact-rated units run $8000 to $25000. PGT parts themselves usually have to be sourced through a dealer or the manufacturer, so most jobs are not a same-day fix – we tell you the real lead time when you call.
How owners usually find us: a PGT casement that won’t crank shut all the way. A sliding patio door that drags on the sill. Fog between the panes on a bedroom window. Or a window that has been hard to lock since the last big temperature swing. In Arlington, the swing is the tell. We go from 100-plus degree afternoons to freezing nights, and PGT units built for that range still take a beating on gaskets, seals, and hardware.
Which PGT Models This Applies To
PGT makes a wide lineup, and the part that fits one series won’t fit another. The common residential lines you’ll see in Arlington homes include WinGuard impact units, Aluminum Series sliders and single-hungs, and vinyl new-construction and replacement lines. Impact glass shows up a lot here because of Texas wind-borne debris code in much of the region, and a PGT WinGuard unit uses different glass, different glazing beads, and different hardware than a standard vinyl window from the same brand.
Before we order anything, we look for three things on the unit itself:
- The manufacturer label. PGT puts a label on the frame or sash with a series and model number. Sometimes it’s on the head jamb, sometimes behind the screen, sometimes on the interior face of the frame.
- Rough opening measurements. Width and height taken at the frame, not the glass. A sixteenth of an inch matters on a replacement sash.
- The glass stamp. Tempered, laminated, or impact-rated glass carries a visible etch or stamp. It tells us whether the unit was built to the impact standard your Arlington permit was pulled against.
On the OEM versus aftermarket question: PGT OEM parts are the safe bet for anything structural – sashes, frames, hinges on a swinging door, the roller assembly on a heavy sliding unit. For weatherstripping, screens, crank handles, and lock hardware, a quality aftermarket equivalent is often a real option if the OEM part has a long lead time. We tell you which is which in writing before we order. Barrett & Sons Construction Arlington is an independent service provider and is not affiliated with PGT.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your PGT Windows & Doors Is Failing
Here’s what failure usually looks like, and what’s actually underneath it.
- Fog or condensation between the panes. The seal on the insulated glass unit has failed. Once moisture gets in, the desiccant is spent and the glass won’t clear on its own – the IGU has to be replaced, not cleaned.
- The window won’t crank open or shut smoothly. On a PGT casement or awning, this usually means the operator arm or the hinge track has worn or the sash is binding. Forcing it bends the operator and turns a $150 part into a $400 repair.
- The patio door drags or jumps the track. Rollers wear, tracks fill with grit and grit-and-grease paste, and the door sags on its frame. Sometimes it’s a roller swap, sometimes the whole sliding panel needs rehanging.
- Water staining or soft wood around the frame. PGT units in Arlington take two kinds of water: driving rain from the north and west, and condensate from air conditioning running hard six months a year. If the sill pan wasn’t flashed right at install, the water shows up years later as a soft spot and a stain on the drywall below.
- The window won’t lock or the sash sits crooked. On PGT impact units, the lock and keeper are matched to the frame – a misalignment after a settle or a hard close can leave the sash unlocked and out of code compliance for impact rating. That one gets fixed, not ignored.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
What you pay in Arlington depends on whether we’re swapping a part or replacing the unit, and whether the opening is impact-rated.
| Scope | Installed Range |
|---|---|
| Hardware, operator, roller, or lock repair | $150 – $650 |
| IGU (sealed glass unit) replacement | $250 – $900 |
| Single window replacement (standard) | $450 – $1,200 |
| Full window replacement, whole house | $4500 – $15000 |
| Impact window installation | $8000 – $25000 |
| Patio door replacement (sliding or hinged) | $1,200 – $4,500 |
The range is driven by unit size, glass type, whether it’s impact-rated, and how much trim and flashing work the opening needs. We give you a written line-item quote, parts and labor broken out, before anything is ordered. If the scope changes mid-job, you get a written change order first. Every window and door job we complete is backed by the 90-Day Done Right Promise.
DIY or Call Us?
Some window work is safe for a careful homeowner. Some isn’t, and we say so plainly.
Reasonable to check yourself: wiping and lubricating a slider track, cleaning and reseating a screen, tightening a loose crank handle, and confirming the label on the frame so you know what model you have before you call. Those are low-risk and save everyone time.
Where DIY goes wrong: replacing an insulated glass unit yourself. The glass is heavy, it’s fragile at the edges, and setting it wrong voids the seal before it ever sees a Texas summer. Replacing a full sash or a patio door panel yourself is risky because the unit has to come out square and the flashing has to be redone right or you’ll be chasing water in a few years. Pulling a window out of an impact-rated opening also touches your permit and inspection record. That’s not a spot for a YouTube tutorial.
If you’ve got a failed PGT window or door, call (888) 590-9867. We’ll tell you straight whether it’s a part, a unit, or just a track that needs cleaning.
FAQs
PGT units are built well, but in Arlington’s climate most owners see the first real service issue somewhere between 15 and 25 years – earlier on west-facing glass that bakes all afternoon. Hardware and rollers tend to go first, then the sealed glass units, then the frame if water has been getting behind the trim. Call (888) 590-9867 for an honest read on yours.
Often yes. A fogged IGU, a worn operator, a dragging roller, or a lock that won’t catch is a part-level repair, not a full unit replacement, and the cost is a fraction of new windows. Structural damage to the frame or a unit that’s out of square usually means replacement. We’ll tell you which one you’ve got in a free estimate.
Most hardware and roller repairs are an hour or two once the part is on hand. A glass unit swap is half a day. The real variable is sourcing the PGT part, which is why we confirm the model and lead time before we schedule – we don’t promise a date the manufacturer can’t hold.
We order through PGT’s dealer and distribution network based on the label and measurements off your unit, and we use quality aftermarket equivalents only when you agree to it in writing and the part is a non-structural piece. You’ll see the part number and price on your quote before we order. Call (888) 590-9867 to schedule your free estimate.
We also work with KraftMaid, Cambria, and Silestone on the interior side, and we’ve been proudly serving local communities for over 29 years. Questions on a PGT unit? Call Barrett & Sons Construction Arlington at (888) 590-9867 – a live person answers, day or night.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.