Home additions & ADU
Kitchen remodeling
Bathroom remodeling
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Sakrete Home Additions & ADU: The Arlington Owner’s Guide
Sakrete is a mortar and concrete mix brand, so there’s no single “Sakrete part” that fails all at once on an addition – the material shows up in the slab, the footings, the block work, and the repair patches around a home addition or ADU. When the Sakrete work under an Arlington addition goes bad, it’s almost always a mix, cure, or joint problem, and the repair runs $45,000 – $130,000 if the addition itself has to be rebuilt or finished properly, or far less if it’s a targeted patch. We install and repair Sakrete-based addition and ADU work across Arlington. Call (888) 590-9867 to schedule a free estimate.
Owners usually find out the hard way. A hairline crack in the slab widens over a winter. A patio slab poured against the addition starts to heave. A block stem wall shows efflorescence – that white chalky bloom – after a wet spring. Or an inspector flags the footing depth on the ADU and everything stops until it’s corrected.
Key Takeaways
- Sakrete is a mix, not a part; the “failure” is the poured or block work under your Arlington addition.
- Most failures trace to mix ratios, cure time, or missing control joints – not the brand.
- Arlington’s shrink-swell clay soil is the real culprit behind most slab cracks here.
- An addition runs $45,000 – $130,000; an ADU runs $90,000 – $220,000 in Arlington.
Which Sakrete Models This Applies To
Sakrete sells dozens of mixes, and the label tells you what you’re dealing with. The ones that matter for additions and ADUs in Arlington are Concrete Mix (the 80 lb red bag most homeowners grab), High-Strength Concrete Mix (for structural work), Fast-Setting Concrete (post holes and quick patches), Sand Mix and Mortar Mix (block and brick joints), and the Crack-Pac and resurfacing products used for repairs.
How to identify what’s actually under your addition: read the original pour ticket or permit if you have it, look at the bag color and product code on any leftover material in the garage, and measure the exposed slab edge to determine thickness. Standard addition slabs in Arlington are 4 inches with thickened footings at the perimeter; ADU slabs often run 5 to 6 inches depending on the engineer’s spec.
On the OEM-versus-aftermarket question: Sakrete isn’t a proprietary system like a window or cabinet line, so there’s no “Sakrete-only” replacement part. A quality equivalent mix from Quikrete or a local ready-mix supplier does the same job when the spec is followed. What matters is matching psi, cure schedule, and joint layout – not the bag logo. We are an independent service provider and are not affiliated with Sakrete.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Sakrete Home Additions & ADU Is Failing
- Spider cracks spreading across the slab. Usually plastic shrinkage cracking from too much water in the mix or a pour done in direct July sun without a curing compound.
- Heaving or dipping at the slab edge. Arlington’s expansive clay soil swells and shrinks with moisture; a footing that wasn’t deep enough will lift the slab as the ground moves.
- White powder bloom on block or stem walls. Efflorescence means moisture is moving through the masonry – often a missing capillary break or a footing that stays wet.
- Crumbling or soft mortar joints. A mortar mix that was too lean, or a freeze during cure, leaves joints that fail a fingernail test.
- Doors and windows that won’t close on the addition. Not a part failure on its own, but a sign the slab has settled or he has shifted the framing out of square.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Arlington, a full home addition runs $45,000 – $130,000 and an ADU runs $90,000 – $220,000. A garage conversion – often the cheapest path to an ADU – runs $30,000 – $80,000. If the Sakrete issue is a repair only, expect a few hundred to a few thousand depending on scope.
The range is driven by square footage, foundation type, whether utilities have to be trenched, and finish level. Every quote we write is line-itemed – mix, labor, forms, rebar, curing compound, permit, inspection – so you can see what the Sakrete portion actually costs versus everything around it. Change orders come in writing before work proceeds, and the finished job is backed by our 90-Day Done Right Promise.
DIY or Call Us?
You can safely check a few things yourself: look for cracks wider than a credit card, check that downspouts drain away from the addition, and confirm the slab edge is visible above grade. What you shouldn’t do yourself is pour or patch structural Sakrete concrete under an addition or ADU. Footing depth, psi, cure time, and joint layout all have to match the permit drawings. A bad patch on a stem wall can hide a moisture problem that rots the framing for years. If the inspector is involved, correcting the work after the fact is far more expensive than doing it right the first time. Call (888) 590-9867 and we’ll walk the foundation with you.
FAQs
A properly mixed, cured, and jointed Sakrete slab lasts 30 to 50 years in Arlington, but our clay soil is hard on it. Slabs without control joints or with undersized footings often show movement within 5 to 10 years.
Sometimes. Hairline cracks and cosmetic efflorescence can be patched and sealed. Slabs that have heaved or settled more than about a half inch usually need underpinning or replacement – the crack is a symptom, not the problem.
A patch or joint repair is a one- to two-day job. A footing correction or slab replacement under an addition runs one to three weeks depending on cure time and inspections, and an ADU foundation is scheduled around the permit review in Arlington.
We spec by psi and application, not by brand loyalty. For most addition slabs in Arlington we use a 3,000 to 4,000 psi mix from Sakrete or an equivalent ready-mix supplier, matched to the engineer’s drawing and the inspector’s requirements.
If your addition or ADU has a Sakrete problem you can see, we’d rather look at it now than after the next freeze. Call (888) 590-9867 for a free estimate and a free second opinion on any written estimate you already have. We also work with KraftMaid, Cambria, and Silestone on the finish side of additions.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.