Bathroom remodeling
Kitchen remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Bathroom Remodeling: The Arlington Owner’s Guide
Schluter bathroom remodeling in Arlington runs $9,000 – $28,000 installed, and most of that spread comes down to how much waterproofing and shower system work your project includes. A tile shower rebuilt over a Schluter KERDI shower system, with the drain, membrane, and curbless pan matched correctly, sits near the top of that range. A smaller room using KERDI-BOARD on the walls and a standard drain assembly lands closer to the bottom.
Owners usually don’t start with the brand name. They start with a soft spot at the curb, a drain that rocks underfoot, or grout that keeps coming back dark along the shower floor no matter how often it’s sealed. By the time they call us in Arlington, the shower has usually been leaking quietly for a season or two, and the tile is the last thing to show it.
Key takeaways
- Installed Schluter bathroom remodeling in Arlington: $9,000 – $28,000.
- Walk-in shower installation on a Schluter system: $4,500 – $12,000.
- Tub-to-shower conversion: $3,500 – $10,000. Shower replacement alone: $3,000 – $8,500.
- Barrett & Sons Construction Arlington is an independent remodeling company. We are not affiliated with Schluter and we don’t speak for them.
Which Schluter Models This Applies To
Schluter has been making shower waterproofing long enough that Arlington homes carry several generations of it under the tile. The pieces you’re most likely to be dealing with:
- KERDI-SHOWER-KIT and KERDI-SHOWER-T/-TS trays. Pre-sloped foam pans in standard sizes and a few off-sizes. The tray and the drain must match: a KERDI-DRAIN body with the KERDI-SHOWER-KIT gets a different drain assembly than a KERDI-LINE linear drain, and mixing the two is one of the most common ordering mistakes we correct.
- KERDI-LINE. Linear drains for curbless and barrier-free showers. The grate and frame are sold by length and finish, and the channel body has to match the tray or mud bed you’re building.
- KERDI-BOARD. The waterproof backer panel, sold in 1/2″, 3/4″, and 2″ thicknesses. In Arlington we use it as tile backer and as the structural layer in places, and the thickness choice matters more than people think when you’re building a bench or a niche.
- KERDI-BAND, KERDI-FIX, and DITRA. The seam tape, sealant, and uncoupling membrane that hold the system together outside the wet zone.
To identify what you have, pull the drain grate and look at the body underneath, or check the sticker on any leftover tray or board in the garage. Part numbers are printed on KERDI-BOARD edges and on the drain packaging. On the OEM-versus-aftermarket question: Schluter’s own drain assemblies and membranes are worth using as specified. Aftermarket foam trays and generic seam tape are where leaks start, and we won’t put an off-brand membrane under a Schluter drain. They don’t bond the way the system was tested to.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Bathroom Remodeling Is Failing
- Grout that turns dark and won’t stay clean. Water is sitting under the tile because the top layer of the system lost its bond. This is the earliest sign and the easiest to ignore.
- A drain that rocks or a grate that pops out. The drain body has separated from the tray or mud bed. In Arlington we see this most on remodels where the original installer skipped the thin-set under the tray.
- A soft or spongy curb. The curb was built from lumber instead of a Schluter curb or KERDI-BOARD, and it’s been wicking moisture. Push on it with your thumb; it should feel like concrete, not a wet sponge.
- Tile tenting or hollow-sounding spots on the floor. The uncoupling membrane or tray has debonded. Tap the floor with a screwdriver handle and listen for the dead thud.
- A water stain on the ceiling below or soft drywall in the next room. The membrane has failed and water is traveling. Arlington’s clay soils and slab movement work on a shower pan over the years, and a rigid assembly with no allowance for movement tends to show it here first.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Every pricing line below is installed, in writing, before work begins. Scope and allowances go on paper, and any change comes as a written change order before a single tile comes off the wall.
| Scope | Installed range in Arlington |
|---|---|
| Full bathroom remodel with Schluter shower system | $9,000 – $28,000 |
| Small bathroom remodel | $5,000 – $12,000 |
| Walk-in shower installation (Schluter tray and drain) | $4,500 – $12,000 |
| Tub-to-shower conversion | $3,500 – $10,000 |
| Shower replacement only | $3,000 – $8,500 |
| Vanity installation | $800 – $3,000 |
What moves you up the range: linear drain instead of standard, curbless conversion into a slab, larger tile formats, and moving the drain or supply lines. What keeps you down: keeping the existing footprint and reusing the tub or vanity if it’s solid. The parts themselves are a small slice of the bill; labor, tile, and waterproofing prep are the bulk of it. Every eligible job gets permits pulled and inspections signed, and the work is backed by our written 90-Day Done Right Promise. Our crew members have up to 28 years of experience on this kind of work.
DIY or Call Us?
You can safely check a few things yourself. Pull the drain grate with a screwdriver and look at the body. Tap the floor for hollow spots. Push on the curb. Run the shower for ten minutes and watch the ceiling below with a flashlight. That tells you whether it’s a cosmetic problem or a waterproofing one.
Rebuilding a Schluter shower isn’t a weekend job, and it isn’t a beginner job. The membrane seams have to be overlapped and bonded exactly, the tray has to sit flat, and the drain has to seat square – mistakes there don’t show up for months, and by then you’re tearing out new tile. No trip charge inside Tarrant County if you’d rather have us look. Call (888) 590-9867 and a live person picks up. Estimates are free, and a second opinion on any written estimate is free too.
FAQs
A properly installed Schluter shower system typically lasts 25 to 30 years. The failure we see before that is almost always installation rather than product: skipped thin-set under the tray, seams not bonded, or a curb built from wood instead of foam. Our Texas heat and slab movement test it more than a northern installation would.
Sometimes. If the membrane is intact and only the drain grate, sealant, or a few tiles failed, we can repair it. If water has reached the tray or the subfloor, replacement is the honest answer. We’ll tell you which one you’re facing after we open it up, and the price change comes to you in writing before we go further. Call (888) 590-9867 for a free estimate.
Plan on seven to ten working days for a shower replacement, and three to five weeks for a full bathroom remodel. Drying time between waterproofing coats and tile setting is what stretches the calendar, not the labor. We put the schedule in writing up front.
We order Schluter drain bodies, trays, KERDI-BOARD, and membrane through their distribution channels and spec the part number to your model. We don’t carry parts on a truck. The order gets placed when the scope is written, and the part number goes on the paperwork so you can look it up yourself. Premium lines like KraftMaid, Cambria, and Silestone come through the same way.
If you have a part number or a photo of the drain body, call us at (888) 590-9867. We’ll tell you what fits, what it costs installed in Arlington, and when we can start.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.