A Barrett company - serving Arlington, TX

Schluter Home Additions & ADU in Arlington, TX

Home additions & ADUHome additions & ADU
Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
RoofingRoofing
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Schluter Home Additions & ADU: The Arlington Owner’s Guide

We install Schluter water-management and underlayment systems inside home additions and ADUs across Arlington, and a full addition or detached unit typically runs $45,000 – $130,000, with ADU construction at $90,000 – $220,000 and a garage conversion at $30,000 – $80,000. Schluter isn’t a single part you replace in an afternoon – it’s a family of membranes, drains, profiles and edge trims, and owners usually discover the failing one the same way: a hairline crack walks across a new tile field, a shower pan in the new bath smells sour, or grout at a doorway darkens for no reason. In Arlington, that story almost always ends with the same question – who can identify the exact Schluter system in place and redo it right.

Call (888) 590-9867

We’re Barrett & Sons Construction, founded in 1998 and owner-operated right here in North Texas. We’re an independent contractor, not affiliated with Schluter, but we know their systems and we pull the permits before the first membrane goes down.

Key Takeaways

  • Schluter is a system, not one part. The failing component is usually the membrane, drain assembly, or profile edge – and which one matters.
  • Installed addition pricing in Arlington: $45,000 – $130,000 for a home addition, plus ADU and garage-conversion ranges below.
  • Our technicians have up to 28 years of experience reading what’s under tile and behind walls.
  • Every eligible addition gets permits pulled and inspections signed – the inspector works for you, not for us.
  • Backed by the written 90-Day Done Right Promise: if it isn’t done right, Tom comes back and makes it right, one call.

Which Schluter Models This Applies To

Schluter’s water-management and tile-edge products come in a few families, and matching the right one is where most of the anxiety sits. The big names you’ll see inside an addition or ADU are KERDI and KERDI-BAND (the surface waterproofing membrane and its seam strip), KERDI-LINE and KERDI-DRAIN (linear and point drains), DITRA and DITRA-HEAT (uncoupling membranes, the heat version adding a cable), and the SCHIENE, JOLLY and RONDEC edge profiles. The gotcha that trips people up: the same part number can come in different heights and widths tuned to your tile thickness, and a KERDI-DRAIN strainer kit sized for a standard p-trap won’t match a KERDI-LINE linear assembly – they aren’t interchangeable. So before you order anything, find the printed label on the underlying flange, the original spec sheet the builder left, or the drain’s cover plate.

On the OEM-versus-aftermarket question for Schluter specifically: the drain grates and strainer tops are the parts most often swapped for generic equivalents, and that’s the one place we tell owners to stay with Schluter’s own. A mismatch in clamping ring height or weep-path geometry is exactly how a new shower starts molding years early. For profiles and trims, a quality equivalent is fine if the dimensions match to the millimeter.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Schluter Home Additions & ADU Is Failing

You can’t see a membrane, so you read the symptoms. These are the five we find most often in Arlington additions, each with what’s usually underneath it:

  • Cracks walking across a tile floor. A crack that runs in a straight line usually means the uncoupling membrane (DITRA) was skipped or the subfloor flexed under it – North Texas clay soil shifts a lot, and a rigid tile job with no uncoupling layer pulls apart.
  • A sour smell from the new shower. That’s moisture trapped under the tile because the KERDI membrane was left unsealed at a corner, or the weep path in the KERDI-DRAIN was blocked during install.
  • Dark grout at doorways and thresholds. Water wicking up through a missing KERDI-BAND seam – the seam strip is the weak point, and if it was taped without the proper thin-set, it won’t hold.
  • Loose heating cable or cold spots in a warm floor. A DITRA-HEAT mat nicked during tile-setting or a loose connector – and once the mat’s buried, you find it with a thermal camera, not a wrench.
  • Popped or sharp edge profiles. A SCHIENE or RONDEC trim that lifted because it was set with too little thin-set or the wrong depth for the tile – that one you can actually see and feel.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

For a Schluter failure inside an addition or ADU, you’re rarely buying “a part” – you’re buying a correct reinstall. Here’s how the Arlington numbers break down, with the addition build as the anchor:

Scope Installed Range (Arlington)
Home Addition $45,000 – $130,000
ADU Construction $90,000 – $220,000
Garage Conversion $30,000 – $80,000
Kitchen Remodel (inside addition) $14,000 – $45,000
Bathroom Remodel (inside addition) $9,000 – $28,000
Walk-In Shower Installation $4,500 – $12,000

What drives the range on a Schluter repair: how much tile has to come up to reach the membrane, whether the drain assembly is a point or linear unit, and whether the subfloor needs re-leveling. Everything arrives in writing before we start – scope, allowances, and any price change as a written change order. Materials are named brands you can look up, not mystery parts off a van.

DIY or Call Us?

Some of this you can safely check yourself. You can read the label on a drain cover, measure your tile thickness against the profile height, spot a cracked grout line, and photograph the whole scene for a second opinion. What we’d tell you plainly: pulling up a set tile bed to reach a KERDI or DITRA membrane is a skilled job, and if you cut blindly you can scribe a heating cable or open a waterproofing layer that then leaks for months. There’s no high-tension danger here like a garage spring, but there is real hidden damage – and an amateur reinstall is how a $2,000 drain job turns into a $9,000 shower rebuild. If water is moving where it shouldn’t, stop and call. The 90-Day Done Right Promise and background-checked crew members mean the people in your home carry the Barrett & Sons name.

FAQs

How long should a Schluter system last? A properly installed KERDI shower or DITRA floor should hold up for decades, but in Arlington’s clay soil and humidity, subfloor movement is the real limit – uncoupling done right is what gets you the long life. Call (888) 590-9867 for a free estimate on a replacement.

Can the Schluter part be repaired instead of replaced? Sometimes – a single popped edge profile or a cracked grout line can be reset, but a failed waterproofing membrane or drain almost always needs the tile opened up to fix it right. Call (888) 590-9867 and we’ll tell you honestly which one you’re looking at, free.

How long does the swap take? A profile or trim reset is a matter of days; a membrane or drain replacement behind tile runs longer because tile removal and reinstall are part of the job – a walk-in shower redo in Arlington runs about $4,500 – $12,000. Call (888) 590-9867 for an exact timeline on your scope.

How do you source the right Schluter part? We match the exact model first – reading the flange label or spec sheet before we order – and we use Schluter’s own drain and membrane components rather than generic swaps, because that’s where shortcuts cause repeat leaks. Call (888) 590-9867 and we’ll help identify yours.

If your addition or ADU is leaking, cracking, or smelling like it shouldn’t, don’t put it off – water finds a way through. Call Barrett & Sons Construction Arlington at (888) 590-9867 for a free estimate. We’ll identify the Schluter system in place, show you the scope in writing, pull the permits, and back it all with the 90-Day Done Right Promise. We also install KraftMaid, Cambria, and Silestone in kitchens and baths across Arlington and the surrounding communities.

Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.

Need Construction help nationwide? Licensed & insured · free written estimates
Call (888) 590-9867
Local Service Coverage

Request a Free Estimate in Arlington

Tell us what you need - Barrett & Sons Construction Arlington responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Call Now - 24/7 Dispatch