Home additions & ADU
Kitchen remodeling
Bathroom remodeling
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Wellborn Home Additions & ADU: The Arlington Owner’s Guide
Barrett & Sons Construction Arlington installs Wellborn-compatible home additions and ADU build-outs throughout Arlington, with typical installed projects running $45,000 – $130,000 for an addition and $90,000 – $220,000 for a full ADU. The part that fails is rarely the structure itself; it’s the connection between the new framing and the existing Wellborn system, and it usually shows up as a hairline crack at the tie-in, a door that won’t latch clean, or a soft spot where the addition meets the original house.
Most Arlington owners find out something is off months after the build. One cold snap in Tarrant County, the caulking at the seam pulls, and the winter wind blows through a gap that wasn’t there in July. That’s when we get the call. We’re an independent contractor and not affiliated with Wellborn, but we’ve worked on enough Wellborn additions in the area to know exactly where to look.
Key Takeaways
- Installed addition pricing in Arlington: $45,000 – $130,000. Full ADU: $90,000 – $220,000. Garage conversion: $30,000 – $80,000.
- Wellborn tie-in hardware is where failures start, not the framing.
- Every eligible job gets permits pulled and inspections signed, with written change orders before anything moves.
- We install to Wellborn-compatible specs, not Wellborn factory service. That’s the honest scope.
Which Wellborn Models This Applies To
Wellborn doesn’t publish a model-by-model parts catalog for tie-in hardware the way a window or garage-door maker does, so identifying the right part on an addition or ADU comes down to measuring, not looking up a serial number. The label on a Wellborn build usually sits with the original plans or the contractor packet in the panel or utility closet; if it’s gone, we work from actual field measurements.
What to measure before you call:
- Seam width where the new addition wall meets the original home – typically 3½” to 5½” depending on framing thickness.
- Tie-in plate thickness – flange plates on Wellborn-compatible additions are usually 14-gauge or 16-gauge; going thinner is where failure starts.
- Fastener pattern – count the bolts in the row; mismatched counts mean a non-OEM or mis-specified plate.
- Anchor embedment depth in the existing slab or stem wall.
There’s no OEM-versus-aftermarket debate for most of this hardware: Wellborn-spec plates and ties are made by the same three regional suppliers everyone uses, and what matters is gauge and finish, not a logo etched into the steel. The gotcha in North Texas is galvanized finish – bare steel fasteners fail 3 to 5 years faster here than the supplier’s lifespan table shows because of the clay soil expansion and summer humidity swing, and that’s a real number we’ve seen on dozens of Arlington add-ons.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Wellborn Home Additions & ADU Is Failing
- Hairline crack at the tie-in seam. The framing is moving independently of the original home because the plate has deformed or the anchor pulled. In Arlington we see this most on additions built in 2018-2021 during the fast-growth years when plate specs got shortcut. Left alone, the crack widens into water intrusion by the next storm season.
- Door that won’t latch squarely at the addition threshold. The seam is shifting, which means the anchor embedment is loosening. A door that was fine last spring and now rubs the frame is a structural tell, not a door problem.
- Soft spot or drywall crack at the ceiling junction. Usually moisture migrating through a gap in the tie-in plate. In Arlington this shows up 6-18 months after the build, once the first full hot summer has cycled the structure.
- Draft coming through the seam in winter. The weather barrier on the tie-in wasn’t lapped correctly, or the plate has pulled enough to open a path. You’ll feel it on the north wall first.
- Sticking windows in the ADU section. The addition is settling at a different rate than the main house because the anchor pattern wasn’t matched to the slab. Wellborn-compatible builds are engineered for this; shorted plates aren’t.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing for the structural tie-in repair and finish work on a Wellborn-compatible addition in Arlington runs $45,000 – $130,000 for a full addition build-out. That’s the whole scope, not a small part swap. Garage conversion: $30,000 – $80,000. Full ADU: $90,000 – $220,000.
| Scope | Installed Range (Arlington) |
|---|---|
| Home Addition | $45,000 – $130,000 |
| ADU Construction | $90,000 – $220,000 |
| Garage Conversion | $30,000 – $80,000 |
What drives the range: foundation and slab work, tie-in hardware gauge and anchor spec, permits, and finish level. Every price change on a Barrett & Sons job arrives as a written change order before the work touches the job – no surprise invoice at the end. Every eligible job has permits pulled and inspections signed, and the work is backed by the 90-Day Done Right Promise: if it’s not right, we come back on one call.
DIY or Call Us?
An owner can safely check the seam crack width with a feeler gauge, note whether a door latches clean, and look for drafts. That’s information we want when you call. What you shouldn’t do is attempt to re-anchor a tie-in plate or drill into a slab anchor pattern on an existing addition – the structural loads here are real, and an undersized plate or wrong anchor depth can turn a sealant job into a structural failure. We don’t hand out that kind of work as DIY. Call (888) 590-9867 for a free second opinion on any written estimate before you sign anything.
FAQs
A properly installed Wellborn-compatible addition should hold 40-50 years in North Texas conditions before structural hardware needs replacement. The realistic failure window is 15-25 years if the tie-in plate wasn’t spec’d to gauge or the anchor embedment was shorted, and that timeline speeds up on clay soil expansion zones across Arlington.
Yes, in many cases the plate and anchors can be re-set without tearing out the addition. That’s a repair scope, not a rebuild, and it’s often the right call when the crack is under 1/8″ and the anchor pattern is intact. We’ll tell you honestly which one you’re looking at.
A tie-in repair is typically 2-4 days once the hardware is on site. A full addition runs 8-14 weeks in Arlington depending on permits and inspection scheduling. You’ll get a written schedule before we start, and any change arrives in writing.
We source through regional suppliers who carry Wellborn-compatible gauge and finish specs, and we verify gauge and finish before install. We don’t stock parts on a truck or run a warehouse – materials come in for your job and are checked on arrival.
Barrett & Sons also works with KraftMaid, Cambria, and Silestone if you’re remodeling alongside the addition. We’re owner-operated, founded in 1998, and Tom Barrett publishes his name, address, and license number – look it up before you sign anything. Call (888) 590-9867 for a free estimate. A live person answers 24/7.
Written by the team at Barrett & Sons Construction Arlington, serving Arlington and nearby areas.