A Barrett company - serving Arlington, TX

Wellborn Kitchen Remodeling in Arlington, TX

Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Wellborn Kitchen Remodeling: The Arlington Owner’s Guide

Wellborn kitchen remodeling in Arlington typically runs $14,000 – $45,000 for a full install, with cabinet-only work landing between $4,000 and $13,000 depending on door style, box count, and whether we’re matching existing Wellborn cabinetry or replacing a full run. We’re an independent installer, not affiliated with Wellborn, and we work with the brand because the boxes and hardware hold up in North Texas heat and humidity better than most of what’s sold off a showroom floor. Most Arlington owners call us after a soft-close hinge starts sagging, a drawer glide grinds halfway out, or a cabinet door won’t sit flush anymore – the small failures that turn into a full kitchen conversation once the boxes underneath are checked.

Call (888) 590-9867

Key takeaways

  • Full Wellborn kitchen installs in Arlington run $14,000 – $45,000; cabinet-only work $4,000 – $13,000.
  • Wellborn uses proprietary hinge and glide patterns – aftermarket parts often don’t line up without modification.
  • Every eligible job gets permits pulled and inspections signed.
  • Written change orders go out before any scope change touches the job.
  • Backed by our 90-Day Done Right Promise on every completed kitchen.

Which Wellborn Models This Applies To

Wellborn cabinets have been built in Alabama since 1961, and the part numbers on hinges, drawer glides, and shelf clips changed generation to generation – which is where most DIY parts hunts go sideways. The brand’s cabinet lines (WoodCraft, Aspire, Select, and Estate, among others) don’t all share the same hardware pattern, and even within a line, the hinge used in 2012 isn’t always the hinge used in 2019. Before you order anything, open a cabinet door and look for the sticker on the inside of the door frame or the back of the box. That label will usually carry a model or series code, and that’s the number we need to match the right replacement.

Here’s the compatibility gotcha most Arlington owners run into: Wellborn’s soft-close concealed hinges use a 48mm cup bore and standard 32mm system holes – which sounds universal, but the mounting plate screw spacing on older Wellborn boxes can sit a couple millimeters off from the plate that comes in a generic big-box hinge kit. You’ll bolt the new hinge on, and the door won’t close flush because the plate is sitting proud. We measure the actual plate footprint on the box before we order. Aftermarket glides are a similar story: some will work, but the OEM or OEM-equivalent is the safer call when the drawer box is still solid and you’re only replacing the slider. We also work with KraftMaid, Cambria, and Silestone on the same jobs, but the Wellborn hardware is a different animal.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Wellborn Kitchen Remodeling Is Failing

  • Doors that no longer close flush. Almost always a worn hinge cup or a mounting plate that’s worked its screws loose over years of daily use. The door isn’t warped – the hardware has drifted out of alignment.
  • Soft-close that’s turned into a slam. The dampener inside the hinge has failed. It’s a wear item, and in a Texas kitchen with a south-facing window, the heat cycling accelerates it.
  • Drawers that grind or stick halfway out. The glide rollers have flat-spotted or the track has filled with grit. On older Wellborn boxes, the undermount glide can also lose tension at the detent.
  • Sagging shelves in upper cabinets. The shelf clips have cracked – usually a plastic fatigue issue, worse in kitchens above a running oven or near a dishwasher that vents steam.
  • Cabinet boxes separating at the seams. Glue joints letting go where the humidity swings in Arlington from 30% in winter to 80%+ in summer. This is beyond a parts swap; it’s a structural fix or a replacement.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

For a full Wellborn kitchen remodel in Arlington, expect $14,000 – $45,000. Smaller kitchens – galley layouts, condos, older ranch homes near downtown Arlington – come in around $9,000 – $20,000. If you’re only replacing cabinet runs and keeping your counters and backsplash, cabinet installation runs $4,000 – $13,000. If the job grows into counters, add $2,000 – $6,500 for countertops and $800 – $2,500 for a backsplash. A kitchen island adds $3,000 – $10,000.

What drives the range: door style (a painted shaker is a different price than a glazed raised panel), box count and layout changes, whether we’re pulling a permit for any structural or electrical work, and disposal of the old cabinets. Every quote is a line-item written estimate with allowances spelled out before you sign. If the scope changes mid-job, you get a written change order before we touch it. We don’t do surprise invoices. All work is backed by our 90-Day Done Right Promise.

DIY or Call Us?

You can safely do a few things yourself: measure your door thickness, photograph the hinge and the sticker on the door frame, tighten loose screws on a mounting plate, and check that the cabinet box itself is square with a level. Those steps help us quote you accurately and often save a trip.

Where DIY goes wrong: cabinet work involves load. A wall cabinet full of dishes weighs 100+ pounds, and a hinge that isn’t mounted into solid material can pull out and bring the door down. Drawer glides replaced with the wrong depth can bind and crack the drawer box. And if the boxes themselves are separating at the seams in an Arlington kitchen, bolting new hardware onto a failing box doesn’t fix the problem – it just delays the failure. If you’ve got a cabinet pulling away from the wall, stop and call us. Give us a ring at (888) 590-9867 and we’ll talk through what you’re seeing before you spend a dime on parts.

FAQs

Need Construction help nationwide? Licensed & insured · free written estimates
Call (888) 590-9867
Local Service Coverage

Request a Free Estimate in Arlington

Tell us what you need - Barrett & Sons Construction Arlington responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Call Now - 24/7 Dispatch