A Barrett company - serving Arlington, TX

Windows & Doors Troubleshooting: Common Problems and How to Fix Them

Last updated November 17, 2026

Windows & doorsWindows & doors
Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Windows & Doors Troubleshooting: Common Problems and How to Fix Them

If your door sticks every July but swings free in January, you don’t have a door problem – you might have a foundation problem, and replacing the door won’t tell you that. That single pattern is the one we see most often in older Arlington neighborhoods, and it’s the reason so many homeowners overpay for a fix that never actually touches the cause. A draft you feel along a door frame is frequently a failed latch or a worn strike plate, not a failed seal. Fog between two panes is sometimes a glass swap and sometimes a whole unit. This guide helps you read the symptoms correctly before you spend money on the wrong repair.

Call (888) 590-9867

Quick Answer

Most window and door problems in Arlington come down to one of four causes: worn weatherstripping, a failed glass seal, a shifted frame, or foundation movement affecting how the door sits in its opening. Use a dollar bill and a flashlight to test the weather seal first, check the latch and strike plate second, and look at the frame and floor third. That order saves you from paying for glass when the real fix is a $12 sweep.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Table of Contents

How to Diagnose a Window or Door Problem in Three Steps

You can narrow down almost any window or door complaint with a flashlight, a dollar bill, and ten minutes. The trick is working from the cheapest fix to the most expensive, not the other way around. Most folks start with “the glass must be bad” and work backward. Try it the other direction.

  1. The bill test for drafts. Close the window or door on a dollar bill so half hangs inside and half outside. Pull gently. If the bill slides out with almost no resistance, the weather seal has failed at that spot. Repeat at the corners, the middle of the sill, and the top. A bill that holds snug everywhere tells you the weatherstripping is still doing its job.
  2. The flashlight test for gaps. At night, have someone stand outside with a bright flashlight pointed at the window or door seam while you stand inside in the dark. Any light you see is air you’ll feel in February. Mark those spots with a pencil.
  3. The latch and strike-plate check. Open the door and look at the strike plate on the jamb. If the latch is barely catching, or if you can see a worn groove where the bolt has been dragging, your draft is a hardware problem, not a seal problem. A loose hinge screw or a strike plate that’s drifted an eighth of an inch will pull the door away from the seal on the handle side every time.

Run those three checks before you call anyone. When we walk into an Arlington home for a windows and doors estimate, the first thing we do is ask what the homeowner has already noticed – because a homeowner who’s done the bill test usually hands us a diagnosis and we’re just confirming it. That’s a much better conversation than guessing.

Why Your Window Feels Drafty (and What’s Actually Causing It)

A drafty window is not automatically a bad window. In our experience, roughly a third of “drafty window” calls turn out to be something other than the glass: a failed seal at the edge, a frame that’s racked out of square, or an installation gap behind the trim. Arlington sits in a climate zone that swings from 20-degree mornings in January to 105-degree afternoons in August. That much expansion and contraction works on every seam in the house.

Here’s how to tell the three apart:

  • Weatherstripping failure: The draft is concentrated along one edge, usually the bottom or the handle side. The glass looks fine. The bill test fails in only one or two spots. This is the cheapest fix and the most common.
  • Seal failure: You see fog, condensation, or a haze between the panes. The glass itself feels cool to the touch and the frame is tight. This is a sealed-unit problem, covered in the next section.
  • Frame-level problem: The draft runs the full height of the window, the trim is separated from the drywall, or you can see daylight around the outside of the frame. This usually means the rough opening wasn’t flashed or sealed correctly when the window went in – and that’s the installer’s responsibility, not yours.

One more thing to check before you blame the glass: outlet covers and baseboards on exterior walls. In older Arlington homes we’ve found cold air pouring in through uninsulated wall cavities that had nothing to do with the window at all. If the draft only shows up when the wind blows from the north, that’s a wall issue, not a window issue.

Foggy Double-Pane Glass: Fix It or Replace It?

Fog between two panes means the seal on that sealed glass unit has failed and moisture has gotten in. The good news is you don’t always have to replace the whole window. On a fixed window or a window where the frame is still solid, a glass shop can sometimes swap just the insulated glass unit – the IGU – and leave the frame in place.

When a glass-only fix makes sense:

  • The frame is square, solid, and the window still opens and latches smoothly.
  • The fogging is confined to one pane and the frame shows no rot, warp, or separation.
  • The window is a standard size that a glass supplier can fabricate without a custom order.

When you’re better off replacing the whole unit:

  • The frame is rotted, cracked, or pulling apart at the corners.
  • The window is a builder-grade aluminum unit from the 1980s or 90s, where a new glass pack costs nearly as much as a modern vinyl or fiberglass window with a better U-factor.
  • You’re already planning to re-side or remodel that wall, since the labor overlaps.

One caution: a glass swap fixes the fog, but it doesn’t fix the reason the seal failed. If the window is racked or the house has shifted, the new unit will eventually fog too. That’s worth knowing before you spend the money twice.

The Door-Sticking Pattern That Points to Foundation Movement

This is the section we wish every Arlington homeowner would read before they buy a new exterior door. Door sticking is the most misdiagnosed problem in the trade. The pattern matters more than the symptom.

Ask yourself three questions:

  1. Is it seasonal? If the door sticks in July and August but swings free in December and January, that’s humidity and soil movement, not a bad door. North Texas clay soil expands when it’s wet and shrinks when it’s dry, and the foundation moves with it.
  2. Is the sticking on one corner or across the whole door? A door that rubs at the top corner on the latch side is usually a hinge or sag issue. A door that rubs across the top of the frame, or that binds on the bottom sill, is telling you the opening itself has changed shape.
  3. Are there other signs in the same area? Look at the drywall above the door frame for a hairline crack running diagonally from the corner. Look at the floor near the threshold for a slope. Check whether interior doors in the same hallway also stick.

If you answered yes to the seasonal question and yes to the drywall crack, you’re looking at foundation movement, and it shows up in a lot of the older pier-and-beam homes in Arlington. Replacing the door will not fix it. The door will stick again within a season. The right first step is a foundation evaluation, and the right second step is deciding whether the door needs shimming, adjusting, or replacing once the foundation is addressed.

We’ve seen this enough times in Arlington that it’s usually the first thing we check on a door estimate – because putting a new Andersen or Marvin door into a moving opening is throwing good money after bad, and we’d rather tell you that up front than take the job.

Weatherstripping and Door Sweeps: What Works

These are the two DIY fixes that genuinely work, and they’re the two we recommend homeowners handle themselves. Weatherstripping and door sweeps are inexpensive, they don’t require special tools, and they solve a real problem in about an hour. If your bill test failed at the bottom of a door, a new sweep is a $15 fix and a screwdriver.

What to buy, roughly in order of how often it’s the right answer:

  • Door sweeps: For the bottom of exterior doors. Look for an aluminum carrier with a replaceable vinyl or brush insert. Aluminum outlasts the plastic versions by years, and in a North Texas summer the plastic ones crack.
  • V-strip or foam weatherstripping: For the sides and top of doors and the sash of windows. Foam is cheap and easy but compresses and fails within a couple of seasons. V-strip lasts longer and handles more movement.
  • Magnetic or bulb weatherstripping: For windows that need a tighter seal. More expensive, but they hold up to the temperature swings.
  • Door shoes and thresholds: If the bottom of the door itself is worn, a new threshold with an adjustable sweep covers it. This is the least expensive way to fix a gap that’s too big for weatherstripping alone.

Before you buy anything, clean the surfaces you’re sticking weatherstripping to with rubbing alcohol. The number one reason weatherstripping fails early is that it was applied over dust and old adhesive. Second reason: it was applied in cold weather, when the adhesive won’t set.

If you’re tackling a bigger project alongside the weatherstripping – a new fence, a patio, a driveway – you can find our work on those trades at Fence Installation in Arlington and Driveway & Pavers in Arlington, and it’s often worth combining the visit.

Frame-Level Problems and When They’re the Installer’s Responsibility

Some window and door problems should never be on your dime. If the window was installed in the last few years and you’re seeing water intrusion, air gaps at the rough opening, or trim pulling away from the wall, that’s a flashing and sealing problem – and it belongs to whoever installed it.

How to see it clearly: go outside. Look at the top of the window or door frame where it meets the wall above. There should be a flashing detail that sheds water away from the opening. If you see a bead of caulk alone where flashing should be, that’s the failure point. Caulk is maintenance. Flashing is structure. Caulking over a failed flashing is one of the most common things we undo in Arlington, and it’s the most expensive kind of masking because by the time the caulk gives up, water’s been in the wall for a year or more.

Signs a frame-level problem is genuinely the installer’s responsibility:

  • Water stains or soft drywall inside the house, directly below or beside the opening.
  • A gap you can see daylight through, at the outside edge of the trim.
  • Sagging or heaving of the trim or siding around the opening.
  • Visible caulk lines applied directly over a paper-faced sheathing without any flashing behind it.

In Arlington, permits get pulled and inspections get signed on a lot of exterior work, and the inspector’s job is to catch exactly this kind of shortcut. When a permit and an inspection are on the record, you have a paper trail. When they aren’t, you have somebody’s word. We don’t think that’s a close call.

If you’re worried your frame-level problem is part of a bigger issue – a wall that’s out of square, an addition that’s settled – that’s where Home Additions & ADU in Arlington comes in. We can tell you whether you’re looking at a window problem or something structural, and usually it takes about fifteen minutes to know the difference.

Window and Door Brands Worth Knowing in Arlington

The brands on the market fall into tiers. Knowing the tier saves you from paying a premium for a brand that won’t perform better in a North Texas climate. Two brands we regularly install on Arlington homes are Andersen and Marvin, both of which hold up to the temperature swings here and both of which you can look up by name and warranty. That matters – a window is a 25-year decision, and a brand you can’t find a warranty page for is a brand you’re taking on faith.

What actually distinguishes the tiers, in practical terms:

  • Entry-level vinyl: Fine for a rental or a workshop. Thinner frames, less efficient glass, shorter warranty.
  • Mid-grade vinyl and fiberglass: The sweet spot for most Arlington homes. Better glass packages, sturdier frames, reasonable warranty terms.
  • Premium wood, clad-wood, and fiberglass: Andersen and Marvin live here. Longer warranties, better glass, and a frame that handles foundation and humidity movement better than a hollow vinyl profile.

The other deciding factor is the glass package. In Arlington, low-E coatings with a solar heat gain coefficient in the 0.25 to 0.35 range cut a lot of summer heat load without turning the room into a cave. Ask for the glass specs by name – U-factor and SHGC – rather than accepting “energy efficient” as an answer. That spec matters more than the brand name on the frame.

How North Texas Seasons Stress Windows and Doors

The windows and doors in an Arlington home take more abuse than in most of the country, and the seasonal stress shows up in specific ways. Once you know the pattern, you’ll catch problems early.

  • Summer: Wood frames swell and doors stick. Aluminum frames expand and the seals at the edges can gap. This is the season for visible problems.
  • Fall: Wood dries and shrinks, which opens gaps you didn’t see in July. This is when the drafts show up.
  • Winter: The temperature swing from a 20-degree morning to a 70-degree afternoon can crack old glazing putty and pull weatherstripping away from the frame.
  • Spring: Hail season. Damaged or cracked window frames from hail often go unnoticed until the first hard rain finds the gap.

Do a walk-through of every window and exterior door twice a year, once in October and once in April. Check the bill test, check the seals, and look at the frame around each opening from outside. Ten minutes twice a year catches almost everything before it becomes a repair.

Common Mistakes to Avoid

  • Caulking over a failed flashing. It hides the problem for a season and lets water into the wall behind the caulk. Flashing is the fix; caulk is maintenance.
  • Replacing a door that just needs adjusting. A door that sticks because of foundation movement will keep sticking after you install a new one. Diagnose the foundation first.
  • Buying a new window when the weatherstripping failed. The bill test takes ten minutes. Run it before you price a new window.
  • Skipping the permits on a replacement project. Arlington inspections catch the shortcuts. When the permit and inspection are on record, you have documentation if you ever sell the house.
  • Trusting a phone-quoted price. A window price without a walk-through is a guess. Ask for a written line-item estimate before you compare anyone.
  • Doing a spring walk-through and not a fall one. The fall is when the drafts show up. If you only check in July, you’ll miss the problem that costs you the most in the winter.
  • Assuming the installer owns the problem when you weren’t sure they installed it. Ask for the paperwork. The 90-Day Done Right Promise matters because it’s in writing.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

When to Call a Professional

Call a professional when the diagnosis points to the frame, the foundation, or the glass. If the bill test fails through the weatherstripping you can reach, that’s a DIY fix. If it fails behind the trim, or if you see daylight around the frame, or if the door only sticks in summer, get eyes on it from someone who does this for a living. Age of the home matters too – window and door hardware in a 1970s Arlington house is often past its service life, and small adjustments start adding up faster than a replacement.

Barrett & Sons Construction Arlington offers free estimates in Arlington, and our technicians have up to 28 years of experience. Call (888) 590-9867 to schedule a free estimate – we’ll run the same diagnostic tests you would and tell you honestly if the fix is a $15 door sweep or a new window unit.

Frequently Asked Questions

The Bottom Line

Most window and door problems give you the diagnosis before you spend a dime – if you know what to look for. Test the weather seal with a dollar bill. Test for gaps with a flashlight. Check the latch and strike plate. Watch the seasons. A door that only sticks in summer is a foundation question. A window that fogs is a glass question. A draft at the frame is an installation question. Get the diagnosis right before you get the estimate, and you’ll spend your money once instead of twice.

If any of this points to a fix that’s beyond the dollar-bill stage, our door’s open. You can find our work across the trades at the Barrett & Sons Construction Arlington home page – Kitchens, Bathrooms, Roofing, Windows & Doors, Fences, Driveways & Pavers, Home Additions & ADUs. Call (888) 590-9867 for a free estimate. Every job includes permits pulled and inspections signed, a written scope and written change orders before anything moves, and the 90-Day Done Right Promise – because the only thing worse than a door that sticks is a contractor who won’t come back when it does.

Written by the team at Barrett & Sons Construction Arlington.

Need Construction help in Arlington? Licensed & insured · free written estimates
Call (888) 590-9867
Local Service Coverage

Request a Free Estimate in Arlington

Tell us what you need - Barrett & Sons Construction Arlington responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Call Now - 24/7 Dispatch